background image

20

96815 v.1.0

Note: Please refer to the Banks iQ

 

Software & Installation Kit, Owners 

Manual for software installation and 

operation instruction before beginning 

Section 6, Automatic Transmission 

Learning

The 6.6L Chevy Duramax Trucks 

equipped with the Allison 1000 

5-speed automatic overdrive 

transmission use an adaptive shift 

control logic. This will require the 

transmission to adapt to the additional 

power created by the Banks Power 

products before it will shift properly. 

Failure to follow the sequence can 

result in damage to the transmission.

Perform the following sequence 

at a location where it is safe to 

accelerate without exceeding the 

posted speed limit.

1.

 Set Six-Gun to level one power 

setting, start the truck and allow the 

engine to reach normal operating 

temperature.

2.

 Adjust Six-Gun to level two, power 

setting.

3.

 Drive vehicle for 5 to 10 miles 

ensuring a complete shift cycle though 

each gear. (The transmission shift 

adaptation learning process requires 

15 to 30 complete shift cycles to learn 

new shift program.)

4.

 Increase power level by one and 

repeat 

Step 3

 until the desired power 

level is achieved.

WARNING: Take particular care not 

to do wide open runs in 5th gear 

when in Automatic transmission 

Learning Mode, especially if speed 

loader is installed

.

The Allison 1000 5-speed automatic 

transmission will continually adapt 

to the power output of the engine 

to optimize shift quality.

 The 

transmission will quickly adapt 

to the power setting if the 

driving cycle includes regular 

gear changes at high loads. The 

transmission learning procedure 

will need to be repeated when 

switching back to the higher 

power settings once the 

transmission adapts to the lower 

power settings

. It will be apparent 

when the transmission adapts to the 

lower settings by monitoring the feel 

of the gearshift. Gear changes will 

be noticeably harder when initially 

switching from a higher to lower 

power setting. This will soften as 

the transmission adapts to the new 

setting.

-END, SEcTION 6-

Section 6

AUTOMATIC TRANSMISSION LEARNING

Summary of Contents for Six-Gun 63717





























Reviews: