banks Ram-Air 42155 Owner'S Manual Download Page 17

 

17

OILED AIR FILTER ONLY

: The Banks Ram-Air 

Oiled Air Filter comes pre-oiled 

and no oiling is necessary for 

initial installation. Use Banks 

Ram-Air Filter Cleaning System 

(part#90094), available from Gale 

Banks Engineering to service the 

Air FIlter. Follow the instructions 

included with the cleaning sys-

tem to clean and re-oil your Bank 

Ram-Air Oiled Air FIlter.

1.

PRE-CLEANING

Tap the element to dislodge any large 

embedded dirt, then gently brush with 

a soft bristle brush. NOTE: If complete 

cleaning is not practical at this time, 

reoil the element and reinstall in your 

vehicle.

2.

SPRAY-ON CLEANING

Spray air-filter cleaner liberally onto 

the entire element and let soak for 10 

minutes.

3.

PAN CLEANING

Large air-filter elements can be  

rolled or soaked in a shallow pan of 

air-filter cleaner. Remove immediately 

and let soak for approximately 10 

minutes.

: NEVER use gasoline, 

steam, caustic solutions, strong 

detergents, high-pressure 

nozzles, or cleaning solvents to 

clean the filter element.

 All of 

these can cause harm to the filter 

media as well as SHRINK and HARDEN 

the rubber end caps.

4.

RINSING

Rinse off the element with low-

pressure water. Tap water is okay. 

Always flush from the clean side to 

dirty side. This removes the dirt  

and does not drive it into the filter.

5.

DRYING

Always dry naturally. After rinsing, 

shake off all excess water and let the 

element dry naturally.

6.

AEROSOL OILING

After cleaning air filter always reoil 

before using. Spray air filter oil down 

into each pleat with one pass per 

pleat. Wait 10 minutes and re-oil any 

white spots still showing.

7.

OILING HINTS

Never use a Banks Ram-Air filter 

without oil (the filter will not stop 

the dirt without the oil). Use only air 

filter oil. Air-filter oil is a compound 

of mineral and animal oil blended 

with special polymers to form a very 

efficient tack barrier. Red dye is 

added to show just where you have 

applied the oil. Eventually the red color 

will fade but the oil will remain and 

filter the air. NEVER USE Automatic 

Transmission Fluid. NEVER USE Motor 

Oil. NEVER USE Diesel Fuel. NEVER USE 

WD40, LPS, or other light-weight oils.

8.

REINSTALL

Reinstall your Banks Ram-Air filter 

element with proper care. Make sure 

the element seats properly in the filter 

case. Install the cover making sure it’s 

in the right position. Tighten all the 

nuts, bolts, screws or clips to factory 

specifications.

9.

DO NOT DISCARD

Affix the “Do Not Discard” sticker to 

the filter case (included with every 

Banks replacement element). Make 

sure you put the sticker in a highly 

visible place to alert your mechanic 

not to discard.

10.

PERFORMANCE HINTS

Service every 50-100,000 miles on

Section 3

AIR FILTER CLEANING INSTRUCTIONS

Summary of Contents for Ram-Air 42155



















Reviews: