Remote System
User’s Guide
Attention for Installation
(Read this section thoroughly before installation.)
Before using the Remote Sensor, read this manual carefully.
During installation and operation, pay close attention to the safety aspect.
ی
(QVXUHWKHSRZHULVVZLWFKHGRႇGXULQJLQVWDOODWLRQRU
maintenance operations.
ی
Use a regulated power supply, e.g. switch-model type.
6LPSOHUSRZHUVXSSOLHVVXFKDVDIXOOZDYHUHFWL¿FDWLRQW\SH
will cause the permissible ripple rating to be exceed and may
cause malfunction.
ی
Ensure correct connections by reference to the wiring diagram.
ی
To avoid malfunction caused by induction noise, cable should
be kept apart from motor or other power cable.
Mail ：[email protected] Web：http://www.b-plus-kk.com
Wireless Power Supply by
Wiring diagram
Mar 24, 2017 No.T307603/E
Remote Coupler System
8+8 Signal Transmission type
【
Function of each component
】
Signal unit :
Connects detector switches (max.8) and transmits
the detected signals to Remote amplifier.
Driving unit :
Small motors, solenoid valves can be connected.
Remote amplifier:
Provides power for Signal unit and Driving unit,also
passes detected signals from Signal unit to Remote
head.
Remote head :
Supply power to Remote amplifier by means of
inductive coupling. Transmits the detected signal from
Remote amplifier to Base head, control signal from
Base head to Remote amplifier.
Base head :
Supply power to Remote head by means of nductive
coupling. Transmits controll signal from Base
amplifier to Remote head, detected signal from
Remote head to Base amplifier
Base amplifier :
Puts out detected signal from Output head to
controller, also sends power for operating of each
component. And transmits controll signal from
controller to Output Head.
Construction of the system
Dimension
: RC08E-011N-000
: RC08E-011P-000
Base Amplifier
Controller
Power unit
(24VDC)
Standard
switch
Small motor
Solenoid
Remote
amplifier
[
Driving unit
]
[signal unit]
Base
amplifier
Remote
head
Base
head
[Remote]
[
Base
]
Detected sig.
Power supply(24VDC/max.2A)
Power supply
Power
supply
Detected sig.
Control signal
Signal
transmission
Control signal
Power supply
max.8 sig.
RC08E-011N-000(NPN type)
"+1...+8","-1...-8" of Terminal block
②
,and "-1...-8" of Terminal block
③
are connected inside,each other.
RC08E-011P-000(PNP type)
8
8
51
5+
┵ሶบԘ
ౝㇱ࿁〝
㨯㨯㨯㨯㨯
㨯㨯㨯㨯㨯
5+
㨯㨯㨯㨯
8
8
㔚Ḯജ
51
㨯㨯㨯㨯
㨯㨯㨯㨯㨯
㨯㨯㨯㨯㨯
㨯㨯㨯㨯㨯
+0
<10'
┵ሶบԙ
+0276
┵ሶบԚ
176276
Terminal block
②
Terminal block
③
Terminal
block
①
Power supply
Internal
circuit
8
8
51
5+
┵ሶบԘ
┵ሶบԙ
+0276
ౝㇱ࿁〝
㨯㨯㨯㨯㨯
㨯㨯㨯㨯㨯
51
+0
<10'
┵ሶบԚ
176276
8
8
㔚Ḯജ
5+
㨯㨯㨯㨯
㨯㨯㨯㨯㨯
㨯㨯㨯㨯㨯
㨯㨯㨯㨯㨯
㨯㨯㨯㨯
Terminal block
②
Terminal block
③
Terminal
block
①
Power supply
Internal
circuit
Input signal
8 signal ( Input : 8 )
Supp
24VDC +/-1.5V
ON voltage
<=16V
OFFvoltage
>=6V
Load current
7mA/1input
Leakage current
<=1mA
Output signal
9signal(Output : 8,Inzone : 1)
Supply voltage
24VDC +/-1.5V
Residual voltage
<=2.5V
Load current
<=300mA
Leakage current
<=0.08mA
Circuit protection
Short circuit protected
Input
Output
RC08E-011N-000
RC08E-011P-000
Specification of Base amplifer
Applicable Base head
RCH08E-211-PU
Supply voltage
24V DC +/- 10
％
Current consumption
<=150mA
（
Not Head
）
Switching frequency
100Hz
Installation
DIN32/35mm rail
Terminal box
Cable diameter 0.13...1.5mm
2
specification
Stripping length 6mm
"+1...+8","-1...-8" of Terminal block
②
,and "-1...-8" of Terminal block
③
are connected inside,each other.
㧗
2QYGTUWRRN[
㧰㧯㧞㧠㨂
㧙
$CUGCORNKHKGT
㧙5+㧗
٤٤٤
٤٤٤
٤٤٤
٤٤٤
٤٤٤
٤٤٤
٤٤٤
٤٤٤
+<
٤٤
٤٤
٤٤
٤٤
٤٤
8
8
٤٤
٤٤
85
1
5
+
8
٤٤
٤٤٤
٤
٤٤
٤٤
51r
$.8
4%*'
9*5+
$-51
$08
I N P U T
1 2 3 4 5 6 7 8
O U T P U T
1 2 3 4 5 6 7 8
$CUGJGCF
Signal from external device
Signal to external device
◆
Total current consumption of signal unit and driving unit must not exceed the rated drive current.
Reduce the switches when the total current consumption exceeds the drive current.
70
110
38
- Terminal blocks were changed since the production in February 2009.
Terminal block
①
Terminal block
②
Terminal block
③
◆
Please note that the signal may become unstable (false
signal or chattering) when the transmission distance and the
center offset are outside the specification range.
◆
The inzone signal is a preliminary signal for confirming that
the output signal is established within the specification range.
Please note that it does not guarantee signals output outside
the specification range.
