background image

INTIMIDATOR™ 12XPC

Model No:  __________________________
Serial No:  __________________________
Engine Make:  _______________________
Serial No:  __________________________
Clutch Make:  ________________________
Model: ___________   S/N  _____________

DEALER:
Name:  _____________________________
Address:  ___________________________
City/State:  __________________________
Phone No:  __________________________
Delivery Date:  _______________________

Copyright 1/18

ATTENTION:

Depending on what  replacement parts you are ordering, we will need the following  information:

CHIPPER COMPONENTS

Serial Number

Model Number of Chipper

ENGINE COMPONENTS

Brand

Engine Serial Number

Engine Model Number

CLUTCH COMPONENTS

Brand

Clutch Serial Number

Clutch Model Number

INTIMIDATOR™ 12XPC

OPERATING & PARTS MANUAL

6750 Millbrook Rd. • Remus, MI 49340 • 1-989-561-2270

MANUFACTURED BY BANDIT INDUSTRIES, INC 

PHONE: 

(

989

)

 561-2270

PHONE: 

(

800

)

 952-0178 IN USA

FAX: 

(

989

)

 561-2273 ~ SALES DEPT.

FAX: 

(

989

)

 561-2962 ~ PARTS/SERVICE

WEBSITE: 

www.banditchippers.com

Summary of Contents for INTIMIDATOR 12XPC


























































































































































Reviews: