Program Remotes
Activate the opener only when door is in full view, free of
obstruction and properly adjusted. No one should enter or leave
garage while door is in motion.
Your garage door opener receiver and Remote Control Transmitter are
set to a matching code. If you purchase additional Remote Controls,
the garage door opener must be programmed to accept the new
Remote code.
To program receiver to match additional Remote Control codes:
1. Press and release the program button on the side of the unit (1).
The green LED will glow steadily for 30 seconds.
2. Within 30 seconds press and hold the button on the hand-held
Remote (2).
3. Release the button when the motor unit light blinks. It has learned
the code. If the light bulb is not installed, two clicks will be hear.
To erase all codes from motor unit memory or to deactivate any
unwanted Remote, first erase all codes:
Press and hold the program button (1) on motor unit until the learn
indicator light goes out (approximately 6 seconds). All previous codes
are now erased. Reprogram each Remote or Keyless Entry you wish
to use.
20
1.
2.
3.
2
1
Replace Light Bulb
Replace light bulb (1) with a 21 watt
maximum light bulb. Insert bulb into
socket as shown. The light will turn
on and remain lit for 2 1/2 minutes
when power is connected. After 2
1/2 minutes it will turn off.
21
1
Install Safety Infrared Beam Kit
(Optional) – (See accessories)
After opener has been installed and adjusted, optional IR beams can
be installed. Instructions are included with this device. It uses an
invisible beam which, when broken by an obstruction, causes a closing
door to open and prevents an open door from closing and is
strongly
recommended for homeowners with young children.
The IR Beams provide an additional measure of safety against a
small child being caught under a garage door.
2
6
1
2
6
0
7
1
2
6
7
7
1
9
5
62173
1702EML
2
3
4
5
6
1
62153
Accessories
(1) Model
59177
Single Function Remote Control
(2) Model
62170
3-Function Remote Control
(3) Model
62162
3-Function Mini Remote Control
(4) Model
62153
Safety Infrared Photo Beams
(5) Model 62173
Wireless Keyless Entry Keypad
(6) Model
59009
Combo Access Device
22
Specifications
Input Voltage . . . . . . . . . . .230 VAC 50/60 Hz
Max. Pull force . . . . . . . . . .600N
Rated Power Input . . . . . . .85 Watts
Rated Load . . . . . . . . . . . .3.0 Nm
Standby Power . . . . . . . . . .9 Watts
Max. Door Weight . . . . . . .60kg
Motor
Type . . . . . . . . . . . . . . . . . .63:1 Worm Gear Reduction
Volts . . . . . . . . . . . . . . . . . .24VDC
Drive Mechanism
Length of Travel . . . . . . . . .2.8M
Travel Rate . . . . . . . . . . . .8cm/sec
Lamp . . . . . . . . . . . . . . . . .24V 21 Watts
Safety
Electronic . . . . . . . . . . . . . .Auto-Force Adjustment
Electrical . . . . . . . . . . . . . .Thermal Fuse in Transformer
Limit Adjustment . . . . . . . .Manual
Dimension
Length (Overall) . . . . . . . . .3.3m
Headroom Required . . . . .30mm
Hanging Weight . . . . . . . . .10kg
Receiver Code Registers
Fixed Code . . . . . . . . . . . .8
Dip Switch . . . . . . . . . . . . .1
Keypad . . . . . . . . . . . . . . . .1
Operating Frequency . . . . .433.92MHz
