B&C Eagle FN1564 Operation And Maintenance Manual Download | Manualshive

Page: 8 / 12

background image

-8-

LOADING

TO PREVENT ACCIDENTAL INJURIES:

• Never place a hand or any other part of the body in nail discharge area of tool while

the air supply is connected.

• Never point the tool at anyone else.
• Never engage in horseplay.
• Never pull the trigger unless nose is directed at the work.
• Always handle the tool with care.
• Do not pull the trigger or depress the trip mechanism while loading the tool.

1.

Insert nails into track of magazine.

2.

Pull pusher all the way back and then allow it to

push nails forward to driving position.

«
...
6
7
8
9
10
...
»

Summary of Contents for FN1564













Reviews:

No comments

Related manuals for FN1564

Brand: Everwin Pages: 14

Brand: Parkside Pages: 16

Brand: Husky Pages: 10

Brand: Campbell Hausfeld Pages: 2

Brand: SALKI Pages: 24

Brand: primatech Pages: 7

PowerStapler 20FS

Brand: Powernail Pages: 12

Brand: Grizzly Pages: 3

Brand: YATO Pages: 88

Brand: Woodstock Pages: 20

Brand: KLINCH-PAK Pages: 10

Brand: Cengar Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands