background image

232SPS2-3903 Manual 

Appendix A: Parallel Port Connections 

A-1 

B&B Electronics  --  PO Box 1040  --  Ottawa, IL  61350 

PH (815) 433-5100  --  FAX (815)  433-5104

 

APPENDIX A:  

PARALLEL PORT CONNECTIONS

 

 

The parallel port connections for the parallel to serial and serial 

to parallel mode are shown in Table A-1, and Table A-2, 
respectively. The connections required are the same for both modes 
of handshaking. The error lines on the parallel port are forced to the 
"no error" states. If the printer is off-line, out of paper, etc., the 
232SPS2 will force the busy line (Pin #11) on the parallel port high 
(logic "1") when in parallel to serial mode. If a error occurs in serial 
to parallel mode, the XOFF character will be sent or DTR will be 
lowered depending on type of flow control used. (NU - Indicates a 
signal is not used or is not “passed through”) 

   

 
 

Table A-1 

Parallel to Serial Mode  

 

DB-25 

Pin # 

Signal Name 

232SPS2 

Direction 

1 Strobe  Input 
2 Data 

bit 

#0 

Input 

3 Data 

bit 

#1 

Input 

4 Data 

bit 

#2 

Input 

5 Data 

bit 

#3 

Input 

6 Data 

bit 

#4 

Input 

7 Data 

bit 

#5 

Input 

8 Data 

bit 

#6 

Input 

9 Data 

bit 

#7 

Input 

10 Acknowledge 

Output 

11 Busy 

Output 

12 PE 

"0" 

Output 

13 SLCT 

“1” 

Output 

14 Auto 

Feed 

Input 

(NU) 

15 Error 

"1" 

Output 

16 INIT 

Input 

(NU) 

17 

SLCT IN 

Input (NU) 

18-25 GND 

 

232SPS2-3903 Manual 

Appendix A: Parallel Port Connections 

A-2 

B&B Electronics  --  PO Box 1040  --  Ottawa, IL  61350 

PH (815) 433-5100  --  FAX (815)  433-5104

 

 

Table A-2  

Serial to Parallel Mode 

DB-25 

Pin # 

Signal Name

232SPS2 

Direction 

1 Strobe  Output 
2 Data 

bit 

#0 

Output 

3 Data 

bit 

#1 

Output 

4 Data 

bit 

#2 

Output 

5 Data 

bit 

#3 

Output 

6 Data 

bit 

#4 

Output 

7 Data 

bit 

#5 

Output 

8 Data 

bit 

#6 

Output 

9 Data 

bit 

#7 

Output 

10 Acknowledge 

Input 

11 Busy 

Input 

12 PE 

Input 

(NU) 

13 SLCT 

Input 

(NU) 

14 Auto 

Feed 

“1” 

Output 

15 Error 

Input 

(NU) 

16 INIT 

“1” 

Output 

17 

SLCT IN 

“1” Output 

18-25 GND 

 

Summary of Contents for 232SPS2















Reviews: