background image

TROUBLE SHOOTING GUIDE

11

PROBLEM

Baby Unit
has no 
Transmission

Transmission
always on

Out-of-range
alarm
always on

Always 
showing low
battery alert

Battery life
is short

Communication
frequently
Interrupted

Too short
Communication
range

POSSIBLE CAUSE

- Mic sensitivity is too low

- Battery has run down or AC 

adapter improperly connected

- Mic Sensitivity is too high

- Unit is set to continuous 

transmission mode

- Baby unit’s battery has run 

down

- Distance between baby and 

parent unit exceeds the 
operating range 

- Pairing is not successful

- Battery has run down

- Battery pack is damaged

- Night light is permanently 

switched on 

- Vibration alert is switched on 

- Baby unit is located near 

other electrical appliances

- Many steel structures 

between baby & parent unit

- Baby unit battery has run 

down

SOLUTION

- Adjust mic sensitivity higher using      
         button  3  
- Replace with new battery or 

check connection

- Adjust mic sensitivity lower using  
        button  2  
- Set the unit to become voice 

activated

- Replace with new battery or use 

AC adapter

- Move the baby & parent unit 

closer together

- Perform pairing again

- Recharge battery using AC 

adapter ( parent unit )

- Replace with new battery or use 

AC adapter ( baby unit )

- Replace with new battery pack

- Switch off night light or set to 

VOX operate

- Switch off vibration alert

- Remove the electrical appliances 

or re-locate the baby unit far 
away from source of interference 
or perform pairing again.

- Re-locate baby or parent unit

- Replace with new battery or use 

AC adapter

Summary of Contents for BC-62















Reviews: