background image

8

Eliminator Vacuum Tank (Tandem) User Manual

Operation Safety

Before each tow check the electrical connection, tail lights, brake lights, and turn signals . Damaged lights or improper electrical 
connection between the tractor and this equipment will result in inoperable lights and/or inoperable electric brakes .
Do not operate on public roads after dark without warning lights . Be alert and avoid loose, soft, or icy surface conditions which 
could cause tipping or loss of control .
Be sure the rear of this equipment has a visible and clean “Slow Moving Vehicle” emblem properly displayed . If towing at 
speeds less than 20 MPH on any public roadway at night, proper warning and running lights are necessary as required by state 
law! 

MAXIMUM TOWING SPEED IS 20 MPH 

DO NOT 

pull this equipment without having safety chains securing this equipment to the tractor . Refer to local transportation 

laws for regulation on safety chain use .
The tractor must be of sufficient size to maintain vehicle stability when this equipment is fully loaded . Never use a tractor that 
is not recommended for this equipment’s application .
ALWAYS use a hitch pin which has a safety clip pin!
If this equipment includes a braking system, check oil level and braking capacity with a full load before operating or moving 
this equipment .
Check the wheel lug bolts and lug nuts daily and tighten as needed .
Replace any parts showing signs of excessive wear, cracking, or likelihood of failure with original equipment service parts .
Be familiar with all valves, doors, gates, and hydraulic controls .

BEFORE USE

 make sure this equipment does 

NOT

 have any foreign objects or materials which can cause equipment damage 

or personal injury .

NEVER ENTER THIS EQUIPMENT UNLESS ABSOLUTELY NECESSARY! 

If entry is necessary, take proper safety precautions 

to include but not limited to:

•  Additional person on site and on the outside near the point of entry
•  Safety harness and ropes where appropriate or required by law
•  Proper life support system where appropriate or required by law
•  Mechanical and electrical power disconnected
•  Contacting your Balzer dealer for more information before entering

Check that the PTO slides freely, is not damaged, and is properly secured to the tractor and this equipment . Make sure there 
is approximately 1/3 overlap of engagement .
When possible, travel straight up or down a slope . Avoid traveling along side of hills, ditches, or other sloped surfaces . Slow 
down prior to going down any steep grade . Never take tractor out of gear when going up or down a hill .
Always check the job site for hazardous terrain, obstructions, or bystanders .
Do not exceed the maximum weight carrying capacity of the equipment or the tractor manufacturer’s maximum towing capacity, 
whichever is the lesser weight . If you have any questions, contact your Balzer dealer .
When agitating a pit, always make sure there is adequate ventilation in any confined area .
Do not stand in front, behind, or along side this equipment when it is in operation or in motion .
When parking this equipment, securely block the wheels before unhitching from the tractor .

Boom Safety

The boom on this unit can extend upward and outward away from the unit . Before operating boom, check surrounding area, 
including above the unit, for any electrical power sources or lines . Electrocution can result if unit comes into contact with 
electrical power sources .

SAFETY

DANGER

ELECTROCUTION can result if unit comes into contact 

with electrical power sources or lines. Check overhead 

and surrounding areas to make sure unit is clear of 

any possible electrical source contact.

Summary of Contents for ELIMINATOR VACUUM TANK Series



























































Reviews: