background image

www.balluff.com

6

Communication functions of the LAN Interface

BVS SC-_1280Z00-07-000

SMART

CAMERA

 IO

English

33

After every status change, the camera sends the new status to the client.

Length in 

bytes

Structure Value

Designation

4

UINT32

42565350

hex

Magic Number

4

UINT32

08

hex

User data length in bytes

4

UINT32

12

hex

Message ID

4

UINT32

Status word. A set bit indicates that the status is 

active (see the following table).

In contrast to the fieldbus interface, the status 

bits do not have to be reset actively. If a status 

is no longer active, the camera simply sends out 

a new status message.

Value

Bit Name

Function description

1

0

Overheat

The camera exceeded the permissible temperature. This 

could lead to a drop in quality of the inspections.
–  Check ambient temperature
–  Check installation conditions

2

1

System Error

Fatal system error. At least one reset is required, a part of 

the camera could be defective.

4

2

Input Container

It is set for input container overflow (more input containers 

than inspections, so that one input container was 

discarded) or underflow (more inspections than input 

containers, so that one input container was used multiple 

times).

16

4

Busy

This bit signals that the camera is currently busy. The bit 

is set while the application is switched over.

128

7

Running

This bit signals that the camera is operating in Run mode.

256

8

Overtriggered

A trigger was rejected by the camera.

512

9

Waiting for Trigger This bit signals that the camera is waiting for a trigger 

signal.

4

UINT32

It defines the endian format of the result 

container and the input data:
0: Little endian

After the conclusion of an inspection, the result is send from the camera to the client with this 

message.

Length in 

bytes

Structure

Value

Designation

4

UINT32

42565350

hex

Magic Number

4

UINT32

User data length in bytes

4

UINT32

20

hex

Message ID

4

UINT32

Application ID. The BVS Cockpit can manage 

several applications, each of which has its own 

ID. This field shows the application that gene-

rated the result container.

x

UINT8[]

Result data as defined in the BVS Cockpit.

6.3.3  Status

6.3.4  Result 

containers

Summary of Contents for BVS SC-M1280Z00-07-000











































Reviews: