background image

246

BVS HS-Q Series
Standard Hand Held Barcode Reader

5

References

5.5.4 Aiming Duration 

Time

Specifies the frame of time the aiming pointer remains on after decoding a label, when in trigger 
single mode. The range for this setting is from 1 to 255 seconds in 1-second increments.

Follow these instructions to set this feature:

1

Determine the desired setting.

2

Pad the result with leading zeroes to yield three digits. For example: 0 = 000, 5 = 005, 20 = 
020, etc.

3

Go to 

page 82

 and scan the ENTER/EXIT PROGRAMMING MODE barcode to enter Pro-

gramming Mode.

4

Scan the barcode: SELECT AIMING DURATION TIME SETTING.

5

Scan the appropriate three digits from the keypad in 

Appendix 18, Use the barcodes in this 

appendix to enter numbers as you would select digits/characters from a keypad.

, that repre-

sent the duration which was determined in the steps above. You will hear a two-beep indica-
tion after the last character.

6

Scan the ENTER/EXIT PROGRAMMING MODE barcode to exit Programming Mode.

This completes the procedure. See 

Table Aiming Duration Time Setting Examples

 for some 

examples of how to set this feature.

Aiming Duration 
Time Setting 
Examples

If you make a mistake before the last character, scan the CANCEL barcode

 

to abort and not save the entry string. You can then start again at the begin-
ning.

STEP ACTION

EXAMPLES

1

Desired Setting

1 Second

90 Sec. 

(1.5 min.)

180 Sec. 

(3 min.)

255 Seconds 

(4.25 min.)

2

Pad leading zero(es)

001

090

180

255

3

Scan ENTER/EXIT PROGRAMMING MODE

4

Scan SELECT AIMING DURATION TIME SETTING

5

Scan Three 
Characters From 

Appendix 18, Use the 
barcodes in this appendix 
to enter numbers as you 
would select digits/
characters from a keypad.

‘0’, ‘0’ and 

‘1’

‘0’, ‘9’ and 

‘0’

‘1’, ‘8’ and 

‘0’

‘2’, ‘5’ and ‘5’

6

Scan ENTER/EXIT PROGRAMMING MODE

Summary of Contents for BVS HS-Q Series









































































































































































































































































































Reviews: