Balluff BNI00E7 User Manual Download Page 36

Page: 36 / 42

www.balluff.com

Troubleshooting

Moderate errors always begin with 0xE2XX. The actual IO-Link error code is in the lowest byte,

e.g. 0xE235 for Function not available. If IO-Link errors occur which are not described in this
manual, please refer to the manual for the respective IO-Link device. Warnings are displayed in
the Word area.

Error list

Error code

Source

Classification

Description / Procedure

0x0001

Gateway

Major

Watchdog was tripped.

Take measures to prevent interference -
use shielded cables. Then perform a
restart.

0x0005

Gateway

Major

Internal communication error

See 0x0001

0x0101

Gateway

Moderate

Undervoltage

Check the cyclic bit range to see which
voltage is affected.

0x0102

Gateway

Moderate

Diagnostics

Check the cyclic bit range to see which
port or pin is affected.

0x0103

Gateway

Warning

Station or network number changed
while the system is running

0xD529

Gateway

Major

Internal SW error.

0xD52B

Gateway

Major

MAC initialization failed

0xE243

Gateway

Moderate

IO-Link port is wrong

0xE119

Gateway

Moderate

Incorrect parameter value in the SLMP
telegram

0xE118

Gateway

Moderate

Incorrect Device Validation type

Summary of Contents for BNI00E7











































Search results

Summary of Contents for BNI00E7

Reviews:

Related manuals for BNI00E7

Brands by name

Popular brands

Balluff BNI00E7, User Manual

Search results

Summary of Contents for BNI00E7

Reviews:

Related manuals for BNI00E7

Brands by name

Popular brands