Safe I/O M odule, Safety over IO-Link, IP67 Module
Installation Guide
w w w.balluff.com
BNI IOF-329-P02-Z038
4 safe input ports, 2 safe output ports and 2 multi-function ports
This installation guide is not intended to replace the User's Guide.
Be sure to f ollow the user's guide and saf ety instructions to ensure
proper installation and operation of the product. These can be
downloaded at
http://www.balluff.de
in Service / Download s / P r o d u c t
documentation.
Please contact Customer Service for any additional questions.
Installation and startup of the BNI IOF -329-P02-Z038 are to be
perf ormed only by qualified specialists while observing the specifications
contained in the User's Guide as well as relev ant standards and
directiv es.
Contents
•
1 BNI IOF-329-P02-Z038
•
1 installation guide
•
20 labels
•
4 M12 dummy plugs
•
1 ground strap
•
1 spring washer
•
1 M4x6 screw
The BNI IOF-329-P02-Z038 is a decentralized saf e input and output
module. It can be connected like any standard IO-Link device to a Balluff
PROFINET IO-Link-Master. The safe communication i s d o n e v i a t h e
PROFIsafe protocol.
Module overview
1
Mounting holes
2
Power supply
3
Display incl.
buttons
4
Status LEDs
5
Port LEDs
6-9
Saf e input ports
10-11 Saf e output ports
12-13 Multif unction ports
14
IO-Link port
15
Labels
16
Ground terminal
Mechanical installation
The module is secured by means of two M6 screws and two washer s.
Insulation support is available separately.
Electrical Installation
Grounding
When wiring be sure to observe basic electrical
guidelines. E.g. EN IEC 60204-1 and all additional
standards that are relevant for the respective
application have to be observed.
The ground connection between housing and machine must have
a low impedance and be as short as possible.
Power supply
7/8
” male plug
connector, 5-pin
Pin Function
Description
1
UA
– GND
0 V
2
US
– GND
3
Functional ground
FE
4
US (total current: 4,8 A)
+24 V
5
UA (total current: 8 A)
Only use PELV rated power supplies to energize the saf e I/O
module.
Use a f use or an intelligent power supply that d i sc on n e ct s t h e
v oltage supply in case of overcurrent greater than 9 A.
The sensor and actuator v oltages are not changed in the
BNI IOF-329-P02-Z038. Its input voltage is t h e r ef o r e a l so t h e
input v oltage for the connected devices. Accordingly, the connect-
ed dev ices must be able to handle PELV rated power supply.
To ensure IP67 protection, the connector must be tightene d to a
torque of 1.5 Nm.
IO-Link interface
M12, 4-pin, male
plug connector,
A-coded
Pin Function
Description
1
IO-Link supply voltage
+24 V
2
n.c.
3
IO-Link supply voltage (GND)
0 V
4
IO-Link data
C/Q
To ensure IP67 protection, the connector must be tightened to a
torque of 0.6 Nm.
Safe inputs: Ports 0, 1, 2 and 3
M12, 5-pin, f emale
plug connector,
A-coded
Pin Function
Description
1
U1/TPO1 short-circuit protected,
conf igurable (
/
)
+24 V
(
≤ 500 mA)
2
F-DI2
Channel 2
3
0 V (GND)
0 V
4
F-DI1
Channel 1
5
U2/TPO2 short-circuit protected,
conf igurable (
/
)
+24 V
(≤ 200 mA)
All sensors and actuators must be powered by the voltages provided
by the BNI IOF-329-P02-Z038 at its ports. This applies to the
‘
+24-V supply as well as the ground potential.
To ensure IP67 protection, the connector must be t i g h te n e d to a
torque of 0.6 Nm and the unused ports fitted with M12 plugs.
Safe outputs: Ports 4 and 5
M12, 5-pin, f emale
plug connector,
A-coded
Pin Function
Description
1
n.c.
2
n.c.
3
GND
0 V
4
F-DO1 short-circuit protected,
conf igurable (
/
)
+24 V
(
≤ 2 A)
5
Functional ground
FE
All sensors and actuators must be powered by the voltages provided
by the BNI IOF-329-P02-Z038 at its ports. This applies to the
+24-V supply as well as the ground potential.
Make sure to av oid cross-connections between the output cables.
This can e.g. be done by the measures that are listed in
EN ISO 13849-2 table D.4.
To ensure IP67 protection, the connector must be tightened to a
torque of 0.6 Nm and the unused ports fitted with M12 plugs.
Multifunction ports: Port 6 and 7
M12, 8-pin, f emale
plug connector,
A-coded
Pin Function
Description
1
U2/TPO2 short-circuit protected,
conf igurable (
/
)
+24 V
( ≤ 200 mA)
2
US short-circuit protected
+24 V
( ≤ 500 mA)
3
F-DI1
Channel 1
4
F-DI2
Channel 2
5
1)
DI3
6
U1/TPO1 short-circuit protected,
conf igurable (
/
)
+24 V
( ≤ 200 mA)
7
GND
0 V
8
1,2)
DO1
+24 V
( ≤ 2 A)
1)
The signals DI3 and DO1 are not processed or generated for
saf ety purposes!
2)
Please consider during the hazard and risk analysis and the
design of safety application, that the output DO1 is switched off in
case of a failure.
All sensors and actuators must be powered by the voltages provided
by the BNI IOF-329-P02-Z038 at its ports. This applies to the
+24-V supply as well as the ground potential.
To ensure IP67 protection, the connector must be t i g h te n e d to a
torque of 0.6 Nm and the unused ports fitted with M12 plugs.