Laser
BAE LX-XO-PL018-L_-S4
Dok.-
Nr. 894081 / Mat.-229394-EN-I15;
Subject to changes. Replaces G15
Components and Models
Type code
Light typ
Order code
BAE LX-XO-PL018-L1-S4
Laser, red-light
BAE00KE
BAE LX-XO-PL018-L2-S4
Laser, red-light
BAE00KZ
Included in delivery are:
Laser, 2 pcs M18x1 nuts, manual
Accessories
For operation of the illuminator we offer these accessories:
Article
Type code
Order code
Connector
BCC M415-0000-1A-014-PS0434-100 BCC032M
Aligment Unit
BMS AD-M-002-D18
BAM0038
Sensor holder M18
BMS CS-M-D12-ID18-01
BAM0032
Power supply 0,7A BAE PS-XA-1W-24-007-001
BAE0001
Please order accessories separately!
Safety Notes
Read the operating instructions carefully prior to commissioning.
The device is not a safety component according to EU machine
guidelines. It is prohibited to use this component in any application
where the safety of persons, traffic or machine is depending on the
function of the component.
Mounting, Connection, Commissioning and adjustment are to be
done by specialised staff only.
Protect the device against mechanical forces and impacts.
Any damage from unauthorized manipulation or improper use
voids the direct vendors guarantee and warranty.
Laser Radiation! DO NOT STARE INTO BEAM OR VIEW
DIRECTLY WITH OPTICAL INSTRUMENTS
–
Laser class 2M per DIN EN 60825-1:2007
The CE-Marking means that our products conform to the
requirements of the EC Guidelines 2004/108/EC and 2006/95/EC
Drawing
Technical data
Type code
BAE LX-XO-
PL018-L1-S4
BAE LX-XO-
PL018-L2-S4
Electrical data
Supply voltage Ub
5…30V DC
Operating current
at
25°C and 5 VDC
100
– 110 mA
60
– 70 mA
Output power
25mW
5mW
Optical data
Light source, light type
Laser, red
Projection
Line, homogen
Line, gauss
Aperture angle
45º
10º
Wavelength
640nm
635nm
Focus range
100mm bis ∞
Laser class per
EN 60825-1:2007
2M
1M
Mechanical data
Dimensions in mm
128 x Ø20
108 x Ø20
Connection
M12 connector, 4-pin
Housing material
brass nickel plated, aluminium
anodized
Optical surface
glass
Weight
84g
75g
Ambient data
Degree of protection IEC
60529
IP67
Polarity reversal protected
yes
Ambient temperature range Ta
-
10 °C … +50°C
Storage temperature range
-10
°C … +80°C
Connection
M12 connector, 4-pin
BAE LX-XO-PL018-
L1
-S4 BAE LX-XO-PL018-
L2
-S4
Pin 1: Voltage
Pin 2: TTL - Voltage below ~5V are interpreted as logic 0 or "light off", voltage
levels above ~5V are interpreted as logic 1 or "light on". Please note that the
switching threshold can vary slightly.
Pin 3: Voltage supply -
Pin 4: Analog - Applying a DC voltage between
0…1V at Pin 4, the laser
intensity is controlled. 0V means the laser power is <10% of the nominal
power.1V and above means the laser will achieve 100% of the nominal laser
power. (
Only valid
BAE LX-XO-PL018-L1-S4 )
Modulation:
Analog intensity control (up to 32 steps) and digital TTL Trigger
up to 1 kHz.
General rule:
Note that there is a linear characteristic between the two
voltages! Both control inputs are tolerant to DC voltages up to 25V, therefore
by applying 24V to the laser, it can easily be switched on to 100% by bridging
pins 1, 2 and 4. There is no need for supply of 1V. You cannot destroy the
laser in a 24 Volt system by wrong connections of input pins.
Protection:
over temperature protection and LED pre-failure indicator
Please note:
The value for illumination intensity indicated in following table
refers to a supply voltage of 24 V DC.
Contact
Balluff GmbH
Tel. +49 7158 173-0
Schurwaldstraße 9
Fax +49 7158 5010
73765 Neuhausen a.d.F.
Germany
