manualshive.com logo in svg

Ballard Designs JU020, Assembly Instructions Manual

Share
Download
Ballard Designs JU020 Assembly Instructions Manual Download Page 10

Page 10 of 10

Customer Service: 800-367-2810

Online: www.ballarddesigns.com

S A F E T Y   P R E C A U T I O N S :

• Close the umbrella in windy conditions or when a storm approaches. 

Never allow the umbrella to flap in the wind; this could damage the canopy.

• Do not leave open umbrella unattended. If damage occurs, this is not covered 

by the warranty.

• When adjusting the umbrella, make sure that no person(s) or item(s) are close to the

umbrella. This is important to prevent injury or material damage. 

C A R E   A N D   M A I N T E N A N C E :

• When not in use, close and cover umbrella with a protective cover. 
• If necessary, clean the fabric with lukewarm water, mild detergent, and a sponge.
• Allow a wet canopy to dry slightly opened, but do not leave unattended.
• Wipe sliding marks on the aluminum poles with a damp cloth.

Winter Storage:
• Store in a dry place.
• Any visible defects must be repaired by a professional.

After the Winter:
• Areas subject to turning and sliding can be treated with a non-staining lubricant spray

(silicone-based).

• Check the condition and function of the umbrella. Any defects must be repaired by a

professional.

CAUTION:

Fully assembled, the AG7813 umbrella weighs 

over 500 lbs.

Moving the umbrella fully assembled will increase the risk of damage to your umbrella
and/or can cause serious injury. 

We recommend a two-person team for assembly

and disassembly.

Summary of Contents for JU020











Reviews:

No comments

Brands by name

Popular brands

Load more brands