background image

14 

 

11.

 

Pellet quality requirements 

 

ATTENTION! 

The pellet stove has been tested only with wood pellets with a diameter of 6 – 8 

mm, class EN plus A1, acc. EN ISO 17225-2:2014. The manufacturer accepts no responsibility 

if you use fuel other than that recommended by the manufacturer. 

This pellet stove is made to use pressed wood (pellets). 
There are many products of this type on the market, it is important to choose pellets that 

have the lowest ash content and are not too wet (always ask for a pellet test certificate 

from the supplier). 

The correct functioning of the pellet stove depends on the type and quality of the 

pellets.  

When the pellets are of low quality, the stove must be cleaned frequently. 

Benefits of using pellets: 

-

 

Allow easy loading. 

-

 

Better regulation of fuel quantity. 

-

 

The small size of the pellets allows the precise supply of the fuel. 

-

 

They allow air supply to achieve optimal combustion efficiency. 

The high combustion efficiency is also determined by the low moisture content in 

pellets (constantly below 10% compared to 20% to 30% moisture content of sawn wood). 

-

 

Pellet bags can be stored in a small area in a dry garage, basement, utility room or 

shed. 

Pellets should be stored in a dry place that is not too cold. Cold and wet pellets reduce the 

thermal power of the fuel and require additional cleaning of the combustion chamber . 

Pellets should not be stored near the pellet stove - at least 2 meters away from it. Do not 

crush them. 

The manufacturer of the stove is not responsible for the use of wood pellets with poor 

quality, nor for the poor performance of the pellet stove due to such fuel. 

 

12.

 

Information relating to dismantling and destruction of the stove 

 

Dismantling, disposal and destruction of old, used stoves is the responsibility of the owner. 

       The owner of the stove must comply with all legal regulations of his country and the 

European Union regarding safety and environmental protection. 

The dismantling and storage of materials from the stove can be entrusted to a third party 

authorized to collect and dispose of these materials

 

Summary of Contents for Sofia















Reviews: