26
27
SPECIFICATIONS
Remote Control Power
2 AA Batteries
IR Command Center Power
120 VAC
IR/Visual Equipment Range
*
Up to 30 Feet (7.62 m) ± 30°
Remote Control Dimensions (H x W x D)
9-2⁄16 x 2-10⁄16 x 1-3⁄16 in.
232 x 65 x 31 mm
Remote Control Weight (w/o Batteries)
8 oz (220 g)
./4%3PECIFICATIONSARETYPICAL)NDIVIDUALUNITS
MAYVARY3PECIFICATIONSARESUBJECTTOCHANGEAND
improvement without notice.
* Distance may vary.
TROUBLESHOOTING
02/",%-,%$DOESNOTBLINKWHENYOUPRESSAKEY
3/,54)/.2EPLACETHEBATTERIESWITHTWO NEW!!
alkaline batteries (see page 7).
02/",%-,%$BLINKSWHENYOUPRESSAKEYBUTHOME
entertainment component does not respond.
3/,54)/.-AKESUREYOUAREAIMINGTHE$OLPHINATYOUR
home entertainment component and that you
are within 15 feet of the component you are
trying to control.
02/",%-4HE$OLPHINDOESNOTCONTROLHOME
entertainment components or commands are
not performing properly.
3/,54)/.4RYALLLISTEDCODESFORTHECOMPONENTBRAND
being set up. Make sure all components can
be operated with an infrared remote control.
02/",%-466#2COMBODOESNOTRESPONDPROPERLY
3/,54)/.5SETHE6#2CODESFORYOURBRAND3OME
COMBOUNITSMAYREQUIREBOTHA46CODE
and a VCR code for full operation (see pages
8-11).
02/",%-.OVOLUMEONASECOND46
3/,54)/.&OLLOWINSTRUCTIONSIN#HANGING6OLUME,OCK
(see pages 23-24).
02/",%-#(#(nAND,!34DONOTWORKFORYOUR
RCA TV.
3/,54)/.$UETO2#!DESIGN ONLYTHE
original remote control will operate these
functions.
02/",%-#HANGINGCHANNELSDOESNOTWORKPROPERLY
3/,54)/.)FORIGINALREMOTECONTROLREQUIREDPRESSING
ENTER to change channels, press ENTER on
the Dolphin after entering a channel number.
02/",%-4RIEDh3EARCH-ETHODvANDSTILLCOULDNOTFIND
a working code.
3/,54)/.4RYTHEh3EARCH-ETHODvAGAINAFTERCLEARING
out the device key as follows: Press and
hold ENTER until red light blinks twice, then
release. Next enter 9 - 9 - 2. Then press and
release the device key to be cleared twice.
REASSIGNING DEVICE KEYS
The Dolphin can be set up to control a second
TV or VCR, or any combination of four home
entertainment components. For example, to have
the Dolphin control a TV, a Cable Converter, and
two VCRs, you will need to reassign the unused
RCVR key to operate the second VCR as follows:
/NTHE$OLPHINPRESSANDHOLD3%450UNTILTHE
,%$BLINKSTWICETHENRELEASE3%450
%NTER4HE,%$WILLBLINKTWICE
3. Press VCR once, then press RCVR once.
4. The RCVR key is now ready to be programmed
for your second VCR. (
See VCR Control,
Programming on page 11.
)
To reassign other device keys, repeat steps 1
THROUGHBYSUBSTITUTINGTHEKEYSEQUENCEFROM
the following chart for a desired component:
To Reassign
Perform Key Sequence
46ASND6#2KEY
3%4506#246
46ASND2#62KEY
3%4502#6246
46ASND#",3!4KEY
3%450#",3!446
46BACKTO46
3%4504646
6#2ASND46KEY
3%450466#2
6#2ASND2#62KEY
3%4502#626#2
6#2ASND#",3!4KEY 3%450#",3!46#2
6#2BACKTO6#2
3%4506#26#2
2#62ASND46KEY
3%450462#62
2#62ASND6#2KEY
3%4506#22#62
2#62ASND#",3!4KEY 3%450#",3!42#62
2#62BACKTO2#62
3%4502#622#62
5PONCOMPLETIONOFAREASSIGNMENTTHE,%$WILL
blink twice to confirm your selection. At that time,
you will also need to program the Dolphin to
control the new component (as described earlier
in this document).
