Baker Instrument Company D12R User Manual Download Page 9

 
Safety equipment warnings and CE compliance statements 
 

2/24/2010 | 71-018 V11 EN  
D12R, D6R, D3R Users Manual 

 

in water or other cleaners or solvents. To clean the screen, take a soft water dampened cloth 
and 

gently

 wipe the surface.   

 
Technical assistance / Authorized Service Centers 

See our website at 

information. This information will be marked with an asterisk.  
 

 

 

 

 

Accessory interconnection and use 

The D3R/D6R/D12R are equipped with a footswitch standard. Other accessories, such as the 
AT101ZTX and safety lights are optional. Please see details about these accessories in later 
chapters in this manual. 

 
Intermittent operation limits 

At this time there are no intermittent operation limits to the use of the AWA unit. 
 

Installation requirements 

The unit may be operated 
 

1)

 

Flat on the bottom of the unit, 

2)

 

Flat on the back of the unit, or 

3)

 

Held at an angle using the rotating handle. 

 

There are no ventilation requirements. 
The unit is intended for use in Installation Category II (Portable Equipment) areas and 
pollution Degree II Environments where occasional non-conducting condensing pollution can 
be encountered. 

 
Unpacking the unit 

Carefully remove the following items from the shipping boxes. 
D3R, D6R or D12R 
Power cord 
Operation manual 
 

Pollution Degree II 

(From IEC 61010-1 3.6.6.2) Only non-conductive pollution occurs. However, temporary 
conductivity caused by condensation is expected. 

 
Power requirements 

Using the provided AC power cord, connect the unit to a grounded AC power source.  The 
unit’s power requirements are 100-240VAC, 50-60 Hz, 2 amps AC maximum current draw. 
The unit is fused using 2.5A fast blow fuses. Replace fuses with like type and rating. 
 

Environmental conditions 

1)

 

The unit has been tested for use up to 2000 m. 

2)

 

The tester should only be operated in temperatures ranging from 41 to 104 
degrees Fahrenheit (5° C to 40° C). 

3)

 

This unit is for use at a maximum relative humidity of 80% for temperatures up to 
31 °C decreasing linearly to 50% relative humidity at 40°C. This unit is intended for 
Installation Category II in a Pollution Degree II environment. 

 

 
 

Summary of Contents for D12R





















Reviews: