background image

Consolidated 1982 Series Safety Relief Valve Manual 

 |  4

© 2020 Baker Hughes Company. All rights reserved.

IV.  Safety Alerts

Read – Understand – Practice

1. 

 DANGER: 

High temperature/pressure can 

cause injury. Be sure all system pressure is 

absent before repairing or removing valves.

2. 

 DANGER: 

Don’t stand in front of valve outlet 

when discharging. STAND CLEAR OF VALVE 

to prevent exposure to potentiality trapped, 

corrosive media.

3. 

 DANGER: 

When inspecting a pressure relief 

valve for leakage. BE VERY CAREFUL!

Improper use or repair of 

a pressurized device may 

result in severe personal 

injury or death.

Stand clear of valve 

when outlet is 

discharging. 

Be sure all system 

pressure is absent 

before repairing or 

removing valves.

Heed all container 

label warnings.

XXX

Provide and use  

guarding to prevent 

contact with heated  

and/or pressurized parts.

Do not work with 

valves while under the 

influence of intoxicants 

or narcotics.

1.  

WARNING: 

Allow the system to cool to room 

temperature before cleaning, servicing or 

repairing the system. Hot components or fluids 

can cause severe personal injury or death.

2. 

 WARNING: 

Always read and comply with safety 

labels on all containers. Do not remove or deface 

the container. Do not remove or deface the 

container labels. Improper handling or misuse 

could result in severe personal injury or death.

3.  

WARNING: 

Never use pressurized fluids/gas/air 

to clean clothing or body parts. Never use body 

parts to check for leakage and/or discharge rates 

of valve areas. Pressurized fluids/gas/air injected 

into or near the body can cause severe personal 

injury or death.

4.  

WARNING:

 It is the responsibility of the owner to 

specify and provide guarding to protect persons 

from pressurized or heated parts. Contact with 

pressurized or heated parts can result in severe 

personal injury or death.

5.  

WARNING: 

Do not allow anyone under the 

influence of intoxicants or narcotics to work on 

or around pressurized systems. Workers under 

the influence of intoxicants or narcotics are a 

hazard both to themselves and other employees 

and can cause severe personal injury or death to 

themselves and/or others.

6.  

WARNING:

 Incorrect service/repair could result 

in product/property damage and/or severe 

personal injury or death. 

7.  

WARNING:

 The misuse of a tool or the use of an 

improper tool could result in personal injury and/

or product/property damage. 

Summary of Contents for Consolidated 1982 Series

































Reviews: