Bajaj Pulsar 150 2019 Manual Download Page 9

14

Classic

How  to  Ride  Your  Bike

Running  IN

Proper running-in is important for the better life 

& trouble free performance of the vehicle.
•  During  first  2000  kms  running-in  period  do 

not  exceed  following  speed  limits.

  Kms 

1st  2nd  3rd 

4th 

5th

  0  -  1000 

15 

30 

45 

55 

65

  1000  -  2000 

20 

40 

55 

65 

75

•  Always  keep  the  speed  below  the  limits 

mentioned  in  the  table.

•  Do  not  race  the  engine  excessively.

•  Do  not  start  moving  or  race  the  engine 

immediately  after  starting.  Run  the  engine 

for  a  minute  at  idle  speed  to  give  the  oil  a 

chance  to  work-up  into  the  engine.

Riding the Bike

Before  starting  the  vehicle  &  with  the  ignition 

key  ‘OFF’,  adhere  to  the  following  first  thing  in 

the  morning  or  after  a  long  period  of  non-use 

(whichever  is  the  case).  Depress  the  clutch 

lever completely. Kick the kick lever all the way 

down  to  its  stop,  briskly  a  couple  of  times. 

Release the clutch lever.

Starting  the  Engine  :

•  Keep  the  fuel  tap  to  ON  or  RES  position.

•  Turn  ignition  switch  to  ON  position.

•  Turn  Kill  switch  to  (       )  ON  position.

•  Confirm  that  the  vehicle  (transmission)  is  in 

neutral.

•  If  the  engine  is  cold  or  when  starting  for 

first  time.  Use  choke  for  quick  starting. 

Choke  lever  (A)  is  located  on  LH  side  of 

Carburettor.

•  Keep  the  throttle  completely  closed,  push 

the  starter  button  (        )  or  kick  the  engine 

with  kick  starter  lever.

•  When  the  engine  is  warmed  up  enough  to 

idle  without  using  choke,  return  the  choke 

to  OFF  position.

A  :  Choke  “OFF”

B  :  Choke  “ON”

A

B

13

Classic

Location  of  Parts

A  :  Seat  Release  Cable

A

Fig.  B

1

2

Fig.  C

3

4

Removal  of   Seat

•  Remove  ‘Side  Cover’  LH.
•  Pull  the  ‘Seat  Release  Cable’ 

(A) 

to  release 

seat  lock.  Keeping  cable  pulled,  tap  the 

center  of  seat,  lift  the  seat  from  rear  end 

and  slide  it  towards  tail  lamp  to  remove 

seat.

Fitment  of  Seat

•  Match  &  insert  the  bracket  (

‘1’ 

of  Fig. 

‘B’

of  seat  with  slot  (

‘2’

  of  Fig. 

‘B’

)  provided 

below  fuel  tank  rear  mounting  on  chassis.

•  Push  seat  towards  fuel  tank  and  align  lock 

rod  (

‘3’

  of  Fig. 

‘C’

)  &  seat  lock  (

‘4’

  of  Fig. 

‘C’

).  Then  press  the  seat  in  middle  from  top 

to  lock  the  seat.

Summary of Contents for Pulsar 150 2019

















Reviews: