manualshive.com logo in svg

Bailey Infi 90 IMEDI01, Instruction

Share
Download
Bailey Infi 90 IMEDI01 Instruction Download Page 20

INTRODUCTION

WBPEEUI240759A0   

3 - 1

 

SECTION 3 - INSTALLATION

INTRODUCTION

This section explains how to install the IMEDI01 module. Do

not

 proceed with operation until reading, understanding, and

performing the steps in the order in which they appear.

EDI module installation requires:

1. Setting switches.

2. Setting jumpers.

3. Module mounting unit (MMU) installation which requires
configuring the MMU and inserting the EDI module.

4. Connecting the EDI module to the Ethernet LAN.

After installing the EDI module, function codes must be config-
ured in the multifunction processor (MFP) module. Refer to

Section 4

 for function code configuration information.

This section also includes a firmware/protocol software down-
load procedure used when upgrading or changing the opera-
tion of the EDI module. The firmware is stored in FLASH
memory.

SPECIAL HANDLING

Use the static grounding wrist strap when installing and remov-
ing modules. Static discharge may damage static sensitive
devices on modules in the cabinet. Use grounded equipment
and static safe practices when working with static sensitive
devices. Observe these steps when handling electronic cir-
cuitry:

NOTE: Always use Elsag Bailey’s field static kit (part number
1948385?1 - consisting of two wrist straps, ground cord assembly,
alligator clip, and static dissipating work surface) when working with
static sensitive devices. The kit is designed to connect the techni-
cian and the static dissipating work surface to the same ground point
to prevent damage to the static sensitive devices by electrostatic dis-
charge.

1.

Use Static Shielding Bag.

 Keep the module in the static

shielding bag until you are ready to install it in the system.
Save the bag for future use.

Summary of Contents for Infi 90 IMEDI01


























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands