background image

 

 

 

 

1. Product Overview 

 

Introduction 

1.1

Baicells  Nova430  is  an  advanced  two-carrier  outdoor  eNodeB  based  on  LTE  TDD 

technology,  which  is  developed  by  Baicells.  It  is  capable  of  operating  in  Carrier 

Aggregation (CA) or Dual Carrier (DC) mode / split mode. 

In CA mode, contiguous or non-contiguous channels are aggregated to provide up to 40 

MHz bandwidth. This essentially doubles the downlink capacity when the CA 430 is used 

with all CAT6/7 user equipment. 

In DC mode, each carrier is treated as an independent cell, supporting 96+96 users, and 

each  supporting  5,  10,  15,  or  20  MHz  bandwidth.  Using  a  Nova430  in  DC  mode 

simplifies and streamlines the deployment of split sectors. 

In addition to having the option to operate Nova430 in either CA or DC mode, HaloB (an 

embedded  MME  option)  comes  as  a  default  feature  in  the  base  software.  Baicells's 

patented HaloB solution migrates the necessary core network functions to the eNB. 

 

Features 

1.2

 

Citizens Broadband Radio Service (CBRS) band covers with dual carrier. 

 

Peak rate: (up to) DL 220Mbit/s, UL2x28 (56) Mbit/s with 2x20MHz spectrum, using 

all Cat6/7 or higher UEs. 

 

Support flexible uplink and downlink time slot ratio: 1(2:2), 2(1:3), and high speed 

data transmission. 

 

Support 5MHz/10MHz/15MHz/20MHz operation bandwidth. 

 

96 concurrent users per carrier, 96+96 in DC mode. 

 

Support copper (RJ-45) backhaul, flexible to deploy. 

 

Integrated small cell form factor for quick and easy installation.

 

 

Suitable  for  private  and  public  deployments;  any  IP  based  backhaul  can  be used, 

including public transmission protected by Internet Protocol Security (IPSec). 

 

Support  PoE++  power  supply,  only  one  Ethernet  cable  required  for  data 

transmission and power supply. 

 

Security  services  to  provide  timely  protection  against  potential  security  risks  and 

illegal intrusion. 

Summary of Contents for Nova430














Reviews: