background image

Page 7

For technical questions, please call 1-800-444-3353.

ATV Winch

Symbol

Property or Statement

Wear heavy-duty, cut- and 

abrasion

-

resistant leather gloves.

Wear ANSI-approved safety glasses.

Cut or sever hazard.

Roller entanglement hazard.

Hot surface burn hazard.

Fire hazard.

Caustic chemical (acid) hazard.

Explosion hazard.

Do not loop the wire rope around 

object and hook onto itself.

Do not place finger(s) through hook.  

Fingers may be caught and get 

pulled into fairlead or drum.

Pull hook using strap only.

Do not use winch in overwind orientation. 

(Wire rope enters/exits at the top.)

Use winch only in underwind orientation. 

(Wire rope enters/exits at the bottom.)

Symbol

Property or Statement

VDC

Volts Direct Current

A

Amperes

CCA

Cold Cranking Amperes

HP

Horsepower

fpm

Feet Per Minute

mpm

Meters Per Minute

RP

Revolutions Per Minute

IP

International Protection rating

Classifies the degrees of protection provided 

against the intrusion of solid objects, 

dust, accidental contact, and water.

G8

Grade 8 

A fastener strength rating.

  WARNING! Read all instructions.

 

Failure to follow all instructions listed 

on pages 8 to 11 may result in fire, 

serious injury and/or DEATH. 

The warnings and precautions discussed in this 

manual cannot cover all possible conditions and 

situations that may occur.  It must be understood 

by the operator that common sense and caution 

are factors which cannot be built into this 

product, but must be supplied by the operator.

Brought to You by www.snapwhole.com

Summary of Contents for 68146





























Reviews: