Page 11
7-11
Installation & Operation Manual
SPECIFICATIONS
Sensor
Assembly:
Housing: PEEK
Impeller: 316SS
Shaft: Tungsten Carbide
CS Specific: Torlon
®
Bearing, EDPM O-Rings
HS Specific: Ketron
®
Bearing, Aflas
®
O-Rings
Tee:
Cast Bronze
ENVIRONMENTAL
Fluid Temp.
-4°F to 140°F (-20°C to 60°C) - chilled
40°F to 260°F (4°C to 125°C) - hot
Ambient Temp. -4°F to 150°F (-20°C to 65°C)
Pressure Ratings:
Badger Data Industrial Series 380 BTU Systems
Specifications
MECHANICAL
Sensor Assembly
Mass
< 15lb
Houseing: PEEK
Impeller: 316SS
ELECTRICAL
Shaft: Tungston Carbide
Inputs
CS Specific: Torlon Bearing, EDPM O‐Rings
Power
12‐35VDC
HS Specific: Ketron Bearing, Aflas O‐Rings
9‐28VAC rms
Communication Modbus
Tee
BACnet
Cast Bronze
Output
Scaled Pulse Open Drain
Temperature Rating For Wetted Materials
CS: ‐20F to 180F
MATERIALS
HS: 30F to 250F
Housing
Polycarbonate
Flow Sensor PEEK
Ambient Temperature Rating
Potting Material Polyurethane
‐20C to 65C
Tee
Brass
Pressure Ratings
Sensor Body Sizes
Tee Sizes 0.75", 1", 1.25", 1.5", and 2"
Recommended Design Flow Range
1 to 15 FPS
380CS and 380HS*
Temp** F
Temp F
PSIG
Type
Range
COMMENTS
40
400 380CS
-20 > +180
Torlon Brgs & EPDM seals
60
400 380CS
-20 > +180
Torlon Brgs & EPDM seals
80
400 380CS
-20 > +180
Torlon Brgs & EPDM seals
100
380 380CS
-20 > +180
Torlon Brgs & EPDM seals
120
365 380CS
-20 > +180
Torlon Brgs & EPDM seals
140
350 380CS
-20 > +180
Torlon Brgs & EPDM seals
160
340 380CS
-20 > +180
Torlon Brgs & EPDM seals
180
320
380CS
-20 > +180
Upper Limit for Torlon & EPDM
200
300 380HS
+30 > +250
Ketron Brgs & Aflas seals***
220
280 380HS
+30 > +250
Ketron Brgs & Aflas seals
240
260 380HS
+30 > +250
Ketron Brgs & Aflas seals
250
230 380HS
+30 > +250
Ketron Brgs & Aflas seals
*Rating is based on PvT of Brass RTD fitting.
**Non-Freezing.
***Special: Ketron Brgs & EPDM seals for < +30F.
Accuracy
Flow Calculation: ±1% of Rate
Temperature Calculation: ±1%
BTU Calculation: ±1%
Output Pulse Width
10, 50, 150, 200, or 250mS
Put Image of Dimentional Drawing here
380CS and 380HS*
Temp** F
Temp F
PSIG
Type
Range
COMMENTS
40
400 380CS
-20 > +180
Torlon Brgs & EPDM seals
60
400 380CS
-20 > +180
Torlon Brgs & EPDM seals
80
400 380CS
-20 > +180
Torlon Brgs & EPDM seals
100
380 380CS
-20 > +180
Torlon Brgs & EPDM seals
120
365 380CS
-20 > +180
Torlon Brgs & EPDM seals
140
350 380CS
-20 > +180
Torlon Brgs & EPDM seals
160
340 380CS
-20 > +180
Torlon Brgs & EPDM seals
180
320
380CS
-20 > +180
Upper Limit for Torlon & EPDM
200
300 380HS
+30 > +250
Ketron Brgs & Aflas seals***
220
280 380HS
+30 > +250
Ketron Brgs & Aflas seals
240
260 380HS
+30 > +250
Ketron Brgs & Aflas seals
250
230 380HS
+30 > +250
Ketron Brgs & Aflas seals
*Rating is based on PvT of Brass RTD fitting.
**Non-Freezing.
***Special: Ketron Brgs & EPDM seals for < +30F.
Figure 7: 380 CS & HS Pressure Ratings
MECHANICAL
Mass: Less than 13 lbs.
ELECTRICAL
Inputs
Power: Isolated 12-24 V DC/V AC ±10%
RS-485 is non-isolated to prevent ground faults. Do not share power with other devices.
Badger Meter A1028 plug-in type 120 VAC/12 V DC power supply recommended.
Communication: Modbus RTU
BACnet
MSTP
Output
Scaled Pulse:
Open Drain
0.01 Hz min. to 100 Hz max.
MATERIALS
Housing:
Polycarbonate
Flow Sensor:
PEEK
Potting Material: Polyurethane
Tee:
Brass
