background image

The fuel tank is empty

 

Fill the fuel tank with properly-mixed fuel

 

Squeeze the throttle control and pull the starter rope until the 

engine starts

 

The engine is flooded

 

The spark plug is fouled

 

Replace the spark plug

 

The air filter is dirty

 

Clean or replace the air filter

 

The idle speed is incorrect

 

Adjust the idle speed

 

The fuel is old (over 30 days) and/or improperly mixed

 

Drain the fuel tank and add fresh, properly-mixed fuel

 

The air filter is dirty

 

Clean or replace the air filter

 

The fuel is old (over 30 days) and/or improperly mixed

 

Drain the fuel tank and add fresh, properly-mixed fuel

 

The spark plug is fouled

 

Replace the spark plug

 

The cutting head is bound with grass

 

Stop the engine and clean the cutting head

 

The inner reel is bound up

 

Rewind the line

 

The line is welded

 

Open the cutting head and remove the welded section

 

Stop the unit, push the bump knob and pull the line until 4 inches

 

(102 mm) is outside of the cutting head

 

Not enough line is extended

 

There is oil, cleaner or lubricant in the cutting head

 

Clean and thoroughly dry the cutting head

 

If further assistance is required, contact an authorized service dealer.

 

THE CUTTING LINE ADVANCES UNCONTROLLABLY

 

The line is twisted

Rewind the line

 

The cutting head is dirty

Clean the inner reel and outer spool

 

The cutting head is out of line

Refill the cutting head with new line

 

THE CUTTING HEAD WILL NOT ADVANCE LINE

 

The air filter is dirty

Clean or replace the air filter

 

THE ENGINE LACKS POWER OR STALLS

 

The cutting head is bound with grass

Stop the engine and clean the cutting head

 

THE ENGINE WILL NOT ACCELERATE

 

The fuel is old (over 30 days) and/or improperly mixed

Drain the fuel tank and add fresh, properly-mixed fuel

 

THE ENGINE WILL NOT IDLE

 

The choke lever was not flipped

Refer to 

Starting Instructions 

in the 

Starting and Stopping 

section

 

The fuel is old (over 30 days) and/or improperly mixed

Drain the fuel tank and add fresh, properly-mixed fuel

 

The primer bulb was not pressed enough

Press the primer bulb 10 times or until fuel is visible

 

PROBLEM

 

SOLUTION

 

THE ENGINE WILL NOT START

 

TROUBLESHOOTING

 

18

Summary of Contents for WB31GTF





















Reviews: