5
REPLACEMENT PARTS/MODEL 150
™
50-001
Five Foot Air Hose
50-0011 Eight Foot Air Hose
(
includes 50-023)
50-0211 10 Ft. Braided Air Hose
(swivel connection both ends)
50-2025 10 Ft. Braided Hose
w/transparent inline drainable water trap
50-2014 Moisture Trap (only)
50-010
Needle Chuck
50-013
Valve Casing
50-014
Plunger & “O” Ring
50-0141 “O” Ring
50-015
Valve Screw
50-0161 F Head Assembly
complete (50-0371-3081-3091-50-055)
50-0162 M Head Assembly
complete (50-0372-0382-0392-50-055)
50-0163 L Head Assembly
complete (50-0373-0383-0393-50-055)
50-019
Trigger
50-020
Plunger Spring
50-021
Airbrush Holder
50-022
Protective Cap
50-030
Tube Shank
50-031
Spring Screw
51-011
Needle Tube
50-033
Handle
50-035
Shell (150)
(w/needle bearing)
50-036
Valve Assembly
complete (50-013-014-0141-015-020)
50-0371 F Regulator
50-0372 M Regulator
50-0373 L Regulator
50-0381 F Head & Tip
50-0382 M Head & Tip
50-0383 L Head & Tip
50-0391 F Tip
50-0392 M Tip
50-0393 L Tip
50-0401 F Needle (1 Ring)
50-0402 M Needle (2 Rings)
50-0403 L Needle (3 Rings)
50-042
Back Lever
50-044
Needle Tube Spring
50-046
PTFE Needle Bearing
50-0482 1/4 oz. Color Cup (150)
50-0492 Airbrush Case (SPECIFY MODEL)
50-050
Prepared Beeswax
50-0052 3/4 oz. Jar w/Cover
50-0053 2 oz. Jar w/Cover
50-055
PTFE Head Washer
50-111
Coupling Nut
50-112
Coupling Nipple
50-208
33 mm Jar Adaptor
EXERCISE ONE/FREE HAND CONTROLLED EFFECT
The exercise shown in fig. 1 is accomplished by practicing the triggering technique explained on page 3.
Pull back slightly on the trigger, while air is on, to create a fine line. Approximately half way through your
stroke motion push trigger forward to discontinue paint flow. While continuing your stroke motion slightly
pull trigger back again to re-create your fine line pattern. This exercise will enable you to draw straight
lines without forming dots or puddles at the beginning and end of each line. Fig. 2 is parallel line graduat-
ing from narrow to broad. These are made by releasing more color and at the same time, lifting the air-
brush away from the surface. Practice daily to develop trigger action control. Fig. 3, layout in pencil
1
/
2
inch squares. Airbrush the dots as small as possible and connect dots with straight lines of even tone.
Practice every lesson carefully before proceeding to the next one.
50-0141
50-014
50-013
50-020
50-015
50-036
50-0052
50-0053
50-0482
50-0381
50-0382
50-0383
50-0161
50-0162
50-0163
50-0371
50-0372
50-0373
50-046
50-022
50-019
50-0391
50-0392
50-0393
50-042
50-035
51-011
50-033
50-030
50-044
51-010
50-031
50-0401 50-0402 50-0403
50-001
50-0011
50-111
50-112
50-2011 Hose can be used with
compressor fitting or propel valve
50-2025 (Optional)
50-2014 (Optional)
50-021
(Optional)
50-208
50-055
50-038
*The PTFE needle bearing carries a lifetime warranty
and free replacement at the factory only
