Page 53
B1 - Compliance statements
Appendix B
In this section, you will find the certifications for your BadgePass printer.
Japanese radio frequency interference (VCCI)
This equipment is Class B information technology equipment based on the rules
laid down by the Voluntary Control Council For Interference by Information
Technology Equipment (VCCI). Its use in or close to a residential area may
cause radio interference, in which case, you must take appropriate steps.
Compliance statements
Concerning Safety and Electromagnetic Compatibility of Radio
Equipment (R&TTE 1999/5/CE, 2006/95/CE and 2004/108/CE Directives)
Manufacturer name:
BadgePass Card Printer
Manufacturer address:
14, avenue de la Fontaine
Z.I. Angers Beaucouzé
49070 Beaucouzé, France
Equipment name:
NXT5000
Year of manufacture:
2013
I, the undersigned,
Serge Olivier
,
Declare under my own responsibility, that the product described above
complies with the essential applicable requirements of the 1999/5/CE,
2006/95/CE and 2004/108/CE directives:
Article 3.1 b: (electromagnetic compatibility protection requirement)
Safety standard applied
EN60950-1:2006 + A11:2009 + A1:2010 + A12:2011
EN50364:2001
EN62311:2008
Article 3.1 b: (electromagnetic compatibility protection requirements)
EMC standard applied
EN55022:2006 + A1
EN55024:1998 + A1 + A2
EN61000-3-2:2006
EN61000-3-3:2008
EN301489-3:V1.4.1
Article 3.2: (Good use of the radio frequency spectrum to avoid undesirable interferences)
EMC standard applied
EN302291-2 V1.1.1
Full name: Serge Olivier
Position: R&D Director
Date: 2013
Signature:
EUROPE -
Norway Only: This product is designed for IT power system with phase-
to-phase voltage 230V. Earth grounding is via the polarized, 3-wire power cord.
FI: “Laite on liitettävä suojamaadoitus koskettimilla varustettuun pistorasiaan”
SE: “Apparaten skall anslutas till jordat uttag”
NO: “Apparatet må tilkoples jordet stikkontakt”
FCC Federal Communications Commission notice
Radio frequency interference in the United States
Part 15, Subpart A, Section 15.107(a) and Section 15.109(a) Class B
Digital device.
Additional information:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try the following measures:
- Reorient or relocate the receiving antenna.
- Increase the distance between the equipment and the radio or television.
- Connect the equipment to a circuit other than that to which the receiver is connected.
- Consult the supplier or an experienced radio/TV technician.
Use of a shielded twisted pair cable is necessary to comply with the restrictions laid down by part 15 of the FCC Rules for
Class B digital devices.
consent of Evolis Card Printer may cause harmful interference and void the FCC authorisation to operate this equipment.
It is recommended to respect a distance of 20 cm between user and RFID module when the module is powered.
This device complies with the Industry Canada CNRs applicable to licence-exempt audio devices. Their use is authorised
subject to the following two conditions: (1) the device must not cause interference and (2), the user of the device must
accept any radio interference to which they may be subject even if the jamming is liable to adversely affect operation.
The NXT5000 model complies with the following specification:FCC
Document History
BadgePass NXT5000 USER GUIDE
