background image

Bitstorm Inc. 

 

Bad Boy Xtreme N & MJ 

www.bitstorm.com 

Chapter 1 - Bench Test 

 

Check off items as completed.  

 

Step 1 

 

 

Remove the  protective  cap from  Antenna  connector  and  attach to  Xtreme. 
Finger tight is adequate. 

Do not over tighten.

 

 

Step 2 

(Do this step if an optional Unleashed is included)

 

DUO comes pre-configured with Port 2 PoE disabled. If Unleashed is included, 
power injection must be enabled on Port 2. To enable Port 2 power:

 

 

Open the case by removing the four screws from the back of the Power In-
jector DUO.

 

 

Move 

BOTH

 jumpers 

JP1

 and 

JP2

 to position 

1-2

 

to enable power on Port 2. 

Jumpers come factory configured to positions 

2-3

 which disables

 

power on 

Port 2.      

 

NOTE: Both jumpers must be positioned identically.

 

 

Close case and refasten four screws on back.  

 

Step 3 

 

Connect power to DUO using either AC or DC.

 

 

 
Verify  that  the  Green  LED  is  lit  on  Port  1  (and  Port  2  if  enabled  in  Step  2).  

Note: If Yellow Power Fault LEDs illuminate, it indicates a reverse polarity 
connection.  In this  condition,  circuit  protection  will  prevent  power  being 
applied to Xtreme and Unleashed when connected to Port 1 and Port 2. 

AC 

Plug in an AC Adapter (included) and insert barrel plug into DUO`s 
power connector. 

DC

 

Connect  the  Power  Cable  (included)  to  an  appropriate  power 
source.  Connect  the  red  (or  white  striped)  wire  to  po)  and 
the  solid  black  wire  to  negative(-).  Insert  barrel  plug  into  DUO’s 
power connector. 

Port 2 Power Enabled 

Port 2 Power Disabled 

Summary of Contents for Xtreme N

















Reviews: