background image

3

SAFETY

WARNING! 

NEVER

 

operate the mower unless the discharge guard and either the deflector assembly or the 

vacuum collector adapter are fastened securely in place.

WARNING!

 

Do not work around the mower deck boot or the blower area until you are certain that the mower 

blades and the blower impeller have stopped rotating.

WARNING!

 

To avoid serious injury, perform maintenance on the vacuum collector; 

ONLY AFTER STOPPING 

THE MOWER’S ENGINE AND WAITING FOR ALL MOVING PARTS TO COME TO A COMPLETE STOP.

 

Set the 

parking brake. Always remove the ignition key before beginning maintenance.

WARNING!

 

For your own personal safety,

 

ALWAYS

 

back up the face of slopes.

 

NEVER

 

attempt to mow 

excessively steep slopes, and use caution when turning on any slope.

Safety Alert Symbol

This Safety Alert Symbol means:

 

“ATTENTION! BECOME

ALERT! YOUR SAFETY IS INVOLVED!”

This symbol is used to call attention to safety precautions that
should be followed by the operator to avoid accidents. When
you see this symbol, carefully read the message that follows
and heed its advice. Failure to comply with safety precautions
could result in death or serious bodily injury.

Safety Signs

The signal words

 

DANGER, WARNING,

 

and

 

CAUTION

 

are used on the equipment safety signs. These words are 

intended to alert the viewer to the existence and the degree of hazard seriousness. 

!

DANGER

!

WARNING

!

CAUTION

!

This signal word indicates a potentially hazardous situation which, if not 
avoided, will result in death or serious injury.

This signal word indicates a potentially hazardous situation which, if not 
avoided, could result in death or serious injury.

It may also be used to alert against unsafe practices.

This signal word indicates a potentially hazardous situation exist which, if 
not avoided, will result in minor or moderate injury.

It may also be used to alert against unsafe practices.

White letters on

 

RED

Black letters on

 

ORANGE

Black letters on

 

YELLOW

Summary of Contents for Q0377

















Reviews: