manualshive.com logo in svg

Bacharach 450, Operating & Maintenance Instructions, Page: 71 / 86

Share
Download
Bacharach 450 Operating & Maintenance Instructions Download Page 71

ECA 450 

Maintenance 

Instruction 0024-9400 

67 

4.4.3  HC Sensor Replacement 

 

Unlike the other sensors that are held in place by their associated bayonet 

holders, the HC sensor is plugged into its printed circuit board which, in 

turn, is secured inside the sensor compartment with four screws. Remove this 

board and replace the sensor as follows: 

 

Material Required: 

 

•  Medium Phillips screwdriver 

•  Small flat blade screwdriver 

•  Replacement HC sensor (refer to Section 6.1) 

 

Procedure: 

 

1.

 

Gain access to sensor compartment by first removing two screws from the 

sensor-cover plate, and then removing plate (see Figure 4-3). 

 

2.

 

Unplug the HC sensor’s printed circuit board from its connector jack. 

 

3.

 

Remove the sensor’s printed circuit board by first removing the board’s 

four corner screws, and then lifting the board with the HC sensor 

attached out from the sensor compartment. 

 

4.

 

Unplug old sensor and discard. 

 

5.

 

Remove replacement sensor from its plastic canister; then plug sensor 

into its printed circuit board. 

 

6.

 

Install and secure the HC sensor’s circuit board inside the sensor 

compartment using the screws removed in Step 3. 

 

7.

 

Install sensor-cover plate that was removed in Step 1. 

 

8.

 

Place analyzer in an area of fresh air and turn it ON. After the warm-up 

cycle completes, observe that no sensor error messages should have 

appeared. 

 

9.

 

Calibrate the new sensor per Section 3. 

 

 

 

 

Summary of Contents for 450























































































Reviews:

No comments