Bacharach 450 Operating & Maintenance Instructions Download Page 43

Page: 43 / 86

ECA 450

Operation

Instruction 0024-9400

Use

∧∨

keys to place cursor next to the desired gas whose Oxygen

reference is to be set; then press

ENTER

to display the O

Reference

screen for that gas.

CO Ref to O2

n %

Where: n = Oxygen reference

Use

∧∨

keys to choose desired Oxygen reference value from 0 to 15%.

Press

ENTER

to make the selection and return to O

Reference gas menu

screen.

Repeat Steps 3 thru 5 for remaining gases.

After an Oxygen reference has been set for each gas, press

ESC

to return

to the Setup List screen.

2.17.8 Test ID

Test records can be identified (e.g., the customer’s name, burner number, and

location) by manually entering up to three lines of text, with each line

containing a maximum of 20 alphanumerical characters. This information

will be associated with all succeeding test records, and will appear at the top

of each test record when printed, and at the bottom of saved test records

when viewed on the display. The chosen Test ID remains in effect until such

time as the Test ID is unselected, a new Test ID is selected, or the

instrument is shut off.

Up to 32 Test IDs can be pre-entered for later retrieval.

All pre-entered Test IDs can be downloaded to a personal computer as an

ASCII text file for storage and printing.

2.17.8.1

Enter / Edit Test ID Information

Enter or edit Test ID information as follows:

Press

SETUP

key to display the Setup List screen.

Use

∧∨

keys to place cursor next to “Test ID”; then press

ENTER

display the Test ID menu.

Test ID

      Select Test ID
   ª  Edit Test ID
      Transmit Test ID

Clear Test ID

Summary of Contents for 450























































































Search results

Summary of Contents for 450

Reviews:

Bacharach 450, Operating & Maintenance Instructions, Page: 43 / 86

Search results

Summary of Contents for 450

Reviews: