BabySense V35TX, User Manual

Page: 12 / 18

4.10 Brightness Adjustments
• Press the
MENU/OK
bu�on
(6)
on your Parent Unit and the menu screen will pop up.
• Press the
LEFT
bu�on
(9)
or
RIGHT
bu�on
(7)
un�l the Brightness icon is highlighted in red.
• Then press the
MENU/OK
bu�on
(6)
and a secondary menu with brightness level op�ons will pop up.
• Press the
LEFT
bu�on
(9)
or
RIGHT
bu�on
(7)
to select the desired brightness level (5 levels) and press
the
MENU/OK
bu�on
(6)
to confirm.
• Press the
EXIT
bu�on
(8)
to exit the menu.
4.11 Temperature Se�ng
The temperature reading from the temperature sensor
(22)
at the back of the Baby Unit will be displayed
on the top of the screen. To switch between °F (Fahrenheit) and °C (Celsius) follow the below instruc�ons:
• Press the
MENU/OK
bu�on
(6)
on your Parent Unit and the menu screen will pop up.
• Press the
LEFT
bu�on
(9)
or
RIGHT
bu�on
(7)
un�l the Temperature icon is highlighted in red.
• Then press the
MENU/OK
bu�on
(6)
and a secondary menu with brightness level op�ons will pop up.
• Press the
LEFT
bu�on
(9)
or
RIGHT
bu�on
(7)
to select the desired temperature scale (°F or °C) and
press the
MENU/OK
bu�on
(6)
to confirm.
• Press the
EXIT
bu�on
(8)
to exit the menu.
NOTE:
The temperature default se�ng is
°F
(Fahrenheit).
NOTE:
The monitor features a built-in automa�c temperature alarm. The monitor will alert (visual
indica�on) when the temperature in baby’s room is too high (90°F and higher) or too low (55°F and
lower). This feature cannot be adjusted.
NOTE:
Make sure the temperature sensor is not posi�oned too close to the camera body as it may affect
the correct temperature reading. It is recommended to stretch out the sensor so it is as far away from the
camera body as possible. Also, it is recommended to place the camera in an area where there is good air
circula�on and not in a closed cornered area where the temperature tends to be higher.
4.12 Lullaby & White Noise Se�ng
You can soothe the baby to sleep by playing 4 pre-programmed lullabies from the Baby Unit. The monitor
also features a White Noise sound, which is an effec�ve way to soothe a crying infant and lull your
newborn to sleep. Lullaby and White Noise feature is controlled remotely from the Parent Unit.
• Press the
MENU/OK
bu�on
(6)
on your Parent Unit and the menu screen will pop up.
• Press the
LEFT
bu�on
(9)
or
RIGHT
bu�on
(7)
un�l the Lullaby icon is highlighted in red.
• Then press the
MENU/OK
bu�on
(6)
and a secondary menu with brightness level op�ons will pop up.
• Press the
LEFT
bu�on
(9)
or
RIGHT
bu�on
(7)
to select the desired melody (1-4), a
LOOP
mode or a
White Noise
sound. Press the
MENU/OK
bu�on
(6)
to confirm.
• Press the
EXIT
bu�on
(8)
to exit the menu.
• In order to stop the lullaby playback, go to the “Lullaby Se�ng” menu and select OFF icon.
NOTE:
Once the lullaby func�on is turned on, the lullaby icon will be displayed on top of the LCD screen.
NOTE:
The lullaby default se�ng is OFF.
NOTE:
When playing the lullabies in a loop mode only the 4 melodies are available; the White Noise does
not play in the loop mode.
12