BaByliss PRO V-Blade BAB7476U Quick Start Manual Download Page 9

sides of your head to the back.

•  You should achieve an even length cut all over your head.

For a shorter back and sides, with length on the top:

•  Attach  the  longer  comb  guide  as  required  for  the  top  of  your  

hair – your clipper is supplied with 8 comb guides (grades 1-8). Each 

comb guide is labelled.

•  Switch the clipper on and the blades will start to move.

•  Hold  the  clipper  to  the  front  of  your  hair  with  the  teeth  pointing  

towards the back of your head and move the clipper towards your 

crown. Repeat as necessary, moving in rows from the front and the 

sides of your head to the back.

•  If you then wish to take the back and sides of your hair to a shorter 

length, switch off the appliance and attach a shorter comb guide.

•  Starting  at  the  nape  of  the  neck,  with  the  comb  guide  flat  against 

the head, move the clipper upwards and outwards over the area you 

want to take shorter.

•  Repeat on the sides of the hair, starting with the teeth of the clipper 

pointing upwards and comb guide flat against the area above the ear, 

again moving the clipper upwards and outwards.

Outlining:

•  To tidy up the edges around your cut e.g. neckline and sideburns, 

detach the comb guides.

•  Hold the appliance upside down, so the front of the clipper is facing 

towards your head.

•  Hold the clipper straight on your sideburns or neckline and move the 

clipper downwards. This will give you a clean, smooth finish.

Cleaning & Maintenance

To maintain optimum performance, the appliance should be cleaned 

after each use:

•  Remove  the  comb  guide  -  the  comb  guides  can  be  rinsed  under 

running water.  Please make sure they are dried thoroughly before 

storage or further use.

•  Using the cleaning brush, brush and blow away any remaining hair 

from the blades.

•  Do not disassemble the blades.

Summary of Contents for V-Blade BAB7476U















Reviews: