manualshive.com logo in svg

Baby Lock Pro-Stitcher Premium BLPS6, Installation Manual

Share
Download
Baby Lock Pro-Stitcher Premium BLPS6 Installation Manual Download Page 5

www.babylock.com

2.2  |  Safety

Read these instructions before using the machine

To use the machine safely

1.  Keep hands and loose clothing away from wheels, gears or other moving parts. 

2.  Turn the machine off and unplug the cord in the following cases:

•  when you have stopped using the machine

•  when you replace or remove the quilting machine needle or any other part

•  in case of failure when you use the machine

•  when you check or clean the machine

•  when you leave the machine unattended

3.  Connect the machine directly to the wall outlet. Do not use extension cords.

To increase the life of your machine

1.  Do not store this machine in areas exposed to direct sunlight or high humidity. Never use or 

store the machine near a heater, an iron, a halogen lamp or other hot things. 

2.  Clean the computer monitor with a soft, lint-free rag. If necessary, dampen the rag with a small 

amount of isopropyl alcohol. Do not use any other cleaners on the computer monitor. 

3.  Use only neutral soaps or detergents to clean the carriage. Benzene, solvents and scouring 

powders can damage the machine and therefore should never be used. 

4.  Do not drop or bump the machine.  

5.  Always consult the manual to replace or fix any other part of the machine. 

To repair or adjust the machine

If the machine breaks down or needs adjustment, first check the troubleshooting chart in the 

appendix to inspect and adjust the machine yourself.

How to use this manual

Notes, important notes, and cautions

 

NOTE:

 

A NOTE indicates important information that helps you make better use of Pro-

Stitcher. 

 

Â

IMPORTANT: 

 

An IMPORTANT note provides information that is essential to properly using 

your Pro-Stitcher.  

 

U

CAUTION:

 

A CAUTION indicates a potential for causing harm to your quilting machine, the 

quilt, or to yourself.

 

Summary of Contents for Pro-Stitcher Premium BLPS6

































Reviews:

No comments

Brands by name

Popular brands

Load more brands