background image

16

1. Open the front cover and

rotate the handwheel to bring
the upper looper to its lowest
position.

2. Cut the upper looper thread

just behind the eye of the
upper looper.

3. Remove the lower looper thread from the

thread guide (A).

6. Push on the subsidiary looper with your

finger and rotate it to the left until the tip
of the subsidiary looper is securely
positioned into the eye of the upper
looper.

5. Insert the subsidiary looper

into the hole at the top of
the upper looper shaft.

4. Hook the lower looper thread to

the thread guide (B).

Needle and lower looper threads are
crossing on the edge of fabric.

Correct thread tension

TWO THREAD  SERGING

Two thread serging provides a decorative, yet functional seam known as
the flatlock seam. You can flatlock garments ranging from lingerie to fake
fur coats. When sewing with two threads you can achieve a flat, bulk-free
seam. Using it to seam fake-fur fabrics and hand knit fabrics you will find
that the “stitches” disappear into the nap. Enhance the appearance of
flatlock stitch with the use of decorative threads through the looper.

Besides flatlock seaming, two thread serging also provides a sturdy
means of overedging all fabrics.
This can be combined with speciality threads for decorative edges on
ruffles, hemlines, and borders.

Two thread sewing is accomplished through the elimination of two threads
- the upper looper and either needle. NOTE: Use the LEFT needle for a
wide flatlock stitch; use the RIGHT needle for a narrow flatlock stitch.

to convert from 3-thread to 2-thread sewing

Needle
thread

Top of
fabric

Bottom of
fabric

Lower
Looper
Thread

(A)

(B)

Summary of Contents for A-LINE Lauren BL450A





























Reviews: