BA Pumps & Sprayers TSX400 12 Volt Safe Operating Procedures Download Page 11

0800 833 538 

www.bapumpsandsprayers.com

Honda Engine - Operation

Before operating the engine for the first time, please review the SAFETY INFORMATION in 

the Honda Manual.

Warning! Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and 

even kill you. Avoid any areas or actions that expose you to carbon monoxide.

Operation Instructions:

1. Move the fuel valve lever to the ON position.

2. To start a cold engine, move the choke lever to 

the CLOSED position. To restart a warm engine, 

leave the choke lever in the OPEN position.

3. Move the throttle lever away from the MIN. 
position, about 1/3 of the way toward the MAX. 
position.

4. Turn the engine switch to the ON position.

5. Operate the starter. Recoil starter by pulling 

the starter grip lightly until you feel  
resistance, then pull briskly. Return the  
starter grip gently. 

DO NOT

 allow the starter grip 

to snap back against the engine. Return it gently 
to prevent damage to the starter.

6. If the choke lever has been moved to the 

CLOSED position to start the engine, 

 

gradually move it to the OPEN position as the 
engine warms up.

7. Position the throttle lever for the desired  
engine speed. We recommend moving the  
throttle to full engine speed.

Stopping the Engine:

To stop the engine in an emergency, simply turn 
the engine switch to the OFF position. Under 
normal conditions, use the following  

procedure:

1. Move the throttle lever to the MIN. position.

2. Turn the engine switch to the OFF position.

3. Turn the fuel valve lever to the OFF position.

Summary of Contents for TSX400 12 Volt



















Reviews: