B2 Mono Quattro Owner'S Manual Download Page 3

INPUT

Connect preamp signal cables from
the headunit to RCA Input of 

Mono

.

OUTPUT

Output RCA for signal routing to another amplifier.

POWER & PROTECTION INDICATOR

Power BLUE, Green-lit shows correct operation 

Protect LED, RED-lit shows general malfunction, 

faulty connection or thermal protection 

GAIN ( 6V ~ 0.2V )

Matching the output voltage of the headunit's 
RCA line-outs to 

Mono

 input section.

SUBSONIC FILTER ( 10Hz ~ 50Hz @ 24dB/Oct )

Adjusts the subsonic cut off point to eliminate low 

frequencies. 

BASS BOOST  

Variable bass boost from 0-9 dB @ 45 Hz

REMOTE LEVEL CONTROL PORT

Connection of external level control.

LOW PASS FILTER ( 35Hz ~ 250Hz @ 24dB/Oct )

Adjusts the cut off point for the low pass filter.

PHASE CONTROL

Variable phase adjustment from 0-180 degrees.

OUTPUT MASTER / INPUT SLAVE 

For daisy chain connection of 2 

Mono

 amplifiers 

down to 2 ohms.

 

3. CONTROL & CONNECTION

3-1. 

Mono 

CONTROL & CONNECTION

3-2. 

Quattro

 CONTROL & CONNECTION

INPUT

Connect preamp signal cables from
the headunit to RCA Input of 

Quattro.

OUTPUT

Output RCA for signal routing to another amplifier.

POWER & PROTECTION INDICATOR

Power BLUE, Green-lit shows correct operation 

Protect LED, RED-lit shows general malfunction, 

faulty connection or thermal protection 

INPUT LEVEL

INPUT LEVEL selects Low/High level input from headunit

if you set it to Low, then Rca Jack receives Low input

If you set it to high, then Rca jack receives High input.

 

GAIN ( 6V ~ 0.2V )

Matching the output voltage of the headunit's 
RCA line-outs to 

Quattro

 input section.

SUBSONIC FILTER ( 10Hz ~ 100Hz @ 12dB/Oct )

Adjusts the subsonic cut off point to eliminate low

frequencies. 

BASS BOOST  

Variable bass boost from 0-18 dB @ 45 Hz

 

2

Summary of Contents for Mono Quattro











Reviews: