background image

Introduction 

 

                                                                   

We thank you for pur

chasing our amplifie

rs. Your decision to be part of something di

erent is what we strive for. 

Our products re

flects who 

we are, going to the extent to deliver y

ou our fine

st comes natural. 

to upgrade the stock electrical system. Ensure the system is in accordance with the full perf

ormance of the amplifi

er. 

Better Bass

Better Bass is our philosophy of adding something extra. 

Keep in mind that continious exposure to SPL above 100 dB can seriously

damage your hearing. Today’s high power auto sound systems can easily

produce SPL over 140 dB. Enjoy your music with sense.

Table of contents

Design features   

 

 

 

 

Panel layout 

 

                    4 - 5

Installation 

 

 

 

6

 *Preparations 

  6

 *Power 

connectors 

 6

 

 

*remote & RCA input 

 

6

wiring 

layout 

   7

   

2

speaker wiring - single amp 

 

8

strapped control panel setting 1 

8

 

* strapping / linking steps 

9

strapped control panel setting 2     10

 

* Master / slave    

            10

 

* strapping / linking steps         10

troubleshooting   

 

             11

  

 

 

 

         

       

   

www.facebook.com/sweetlikedanish - www.youtube.com/b2audio - www.b2audio.com - www.twitter.com/b2_audio - wwww.instagram.com/b2_audio

Summary of Contents for SLD5K













Reviews: