background image

INSTALLATION SAFETY INSTRUCTIONS

2

CAUTION:

This mount is intended for use 

only with the maximum weights indicated. Use with 

flat screens heavier than the maximum indicated may result
in instability causing possible injury. 

Do not attempt to install this product until all instructions and warnings have been read and properly understood.

 

Please keep these instructions for future reference. 
Please check carefully to make sure there are no missing or defective parts - defective parts must never be used.  
B-Tech International Limited, its distributors and dealers are not liable or responsible for damage or injury  

 

caused by improper installation, improper use or failure to observe these safety instructions. In such

 

cases, all guarantees will expire.   

General

B-Tech International Ltd recommends that a professional AV installer or other suitably qualified person 
install this product. Great care must always be taken during installation as most AV equipment is of a 
fragile nature, possibly heavy and easily damaged if dropped. 
If you do not fully understand the instructions or are not sure how to install this product safely, then please 
consult a professional for advice and/or to install this product for you. Failure to mount this product 
correctly may cause serious injury or death both during installation and at any time thereafter. 
Do not mount any AV equipment that exceeds the specific weight limit of the product you are installing. 
This weight limit will be clearly stated on each product and its packaging and will vary from product to product. 

Product location

Please pay careful attention to where this product is located. Check load capacity of wall prior to installation 
as some walls are not suitable for installation.  Designed for indoor use, this mount is suitable for public or home 
installation. If located in a public or frequently populated area ensure that the product is out of the immediate 
reach of people. If any AV equipment is to be suspended over the likely path or location of people then great 
care should be taken to secure all parts of the installation from falling.  If you install this product on drywall it 
must be securely fixed to a wooden stud, concrete block or other permanent structure behind the drywall board. 

Installing on drywall boards alone will not support the weight of most AV equipment.  

When drilling holes in walls it is essential to avoid contact with electrical cables and water or gas pipes 
contained within. Use of a good quality live wire detector and hidden object locator is therefore recommended. 
Only drill into structures when you are sure it is safe to do so. 

Fixing hardware

It is highly recommended that all wall fixing screws be used where supplied and that the purpose of all 
other fixing hardware is fully understood. In some cases more AV equipment fixing hardware will be 
supplied to accommodate different models of equipment and set up configurations. 
The installer must be satisfied that any supplied fixing hardware is suitable for each specific installation. 
If any fixing screws or included hardware are deemed not sufficient for a safe installation then please 
consult a professional or your local hardware store. 

Hazard limitation

When routing cables take advantage of any built in cable management features that the product might 
provide and ensure that all cables are tidy and secure. Check to see that any moving aspect of the 
product can do so unhindered by any cabling. 
Some products have moving parts and the potential to cause injury through the crushing or trapping of 
fingers or other body parts. 
Particular attention to the nature of moving parts is required especially when assembling installing and 
adjusting during set up. 
Immediately after installations double-check that the work done is safe and secure. Double-check all 
necessary fixings are present and are of ample tightness. 
It is recommended that periodic inspections of the product and its fixing points are made as frequently as 
possible to ensure that safety is maintained. If in doubt consult a professional AV installer or other suitably 
qualified person. 

Summary of Contents for SYSTEM X BT8341





















Reviews: