B.M.P. ThermicRoll Installation Manual Download Page 33 | Manualshive

Page: 33 / 38

B.M.P. ThermicRoll Installation Manual Download Page 33

Installation Instructions

JAMISON DOOR COMPANY

33

H4494002 REV B

C. Motor Brake Air Gap Adjustment

1. Depress Emergency Stop push button on front of Control panel.

2. Mark location of the brake cable stop location on the brake cable.

3. Disconnect the manual brake cable from the brake lever.

4. Unscrew the brake lever from the brake assembly.

5. Remove Phillips screws from cover on bottom of motor.

6. Check air gap arrow #3 with gauge #4. Gap should be .008-

.020” or .2-.6mm

7. Unbend locking tab on lock washer.#1

8. Turn locknut #2 counter clockwise to increase the gap, clockwise to decrease the gap.

9. Find a tab on lock washer that aligns with notch in locknut and bend that tab to engage.

10. Reinstall motor cover.

11. Reinstall the brake lever.

12. Reconnect the brake cable to the brake lever.

13. Release Emergency Stop button, cycle door to open

position and make sure the door doesn’t drift

shut.

«
...
31
32
33
34
35
...
»

Summary of Contents for ThermicRoll







































Reviews:

No comments