11. Exclude sources of interference
If the detection zone is too large, or areas are covered that should
not be monitored, use the blinds to reduce or limit those areas.
12. Technical data
Power supply:
110-240 VAC, 50/60 Hz
Power consumption:
approx. 1W
Ambient temperature
-25°C to +50°C
Degree of protection/class:
IP20 / II
Recommended height
for mounting:
2 - 3 m
Range of coverage
Ø H 2,5 m / T = 18°C:
seated 4 m / tangential 10 m /
radial 6 m
Area of coverage:
circular 360°
Dimensions H x Ø [mm]
FC
84.5 x 80 mm
Visible part when built into ceiling:
15 x 80 mm
Lux value:
10 - 2000 Lux
• DALI/DSI
digital BUS control wire, 2-core, no polarity (broadcast only)
Max. no. of series-connected electronic ballasts:
up to 50 (broadcast only)
Time settings:
1 - 30 min. / test
• Channel 2
Type of contact:
NOC/with pre-travel tungsten
contact
Contact load:
2300 W, cos
ϕ
=1;
1150 VA, cos
ϕ
= 0,5, µ contact
Declaration of Conformity:
This product respects the directives concerning
1. electromagnetic compatibility (2004/108/EU)
2. low voltage (2006/95/EU)
3. restriction of the use of certain hazardous substances in electrical
and electronic equipment (2011/65/EU)
13. Article / Part nr. / Accessory
Typ
FC
PD2-M-DALI/DSI-1C (Master)
92486
PD2-S (Slave)
92166
LUXOMAT
®
Remote control:
IR-PD-DALI-1C (incl. wall bracket)
92116
IR-PD-DALI-Mini
92112
IR-RC-Adapter with smartphone app
92726
Accessories:
BSK Wire basket
92199
14. LED function indicators
LED function indicators
Process
Standard
mode
Double-locked
Initialisation time
unprogrammed
Red flashes
Green flashes
Initialisation time
programmed
Red
flashes
quickly
Green flashes
quickly
Motion detection
Red
flashes
on each
detected
movement
Green flashes
on each
detected
movement
Too bright detected
Red
flashes
2x per
second
Green flashes
2x per
second
Too bright / too dark /
undefined in opened state
Red
flashes
very quickly
Green flashes
very quickly
Toggle DALI/DSI
DSI active
Red
shines
3 sec.
Toggle DALI/DSI
DALI active
Green shines
3 sec.
Toggle HA/VA
HA active
White shines
permanently
Toggle Preset/User
Preset active
Red
shines
3 sec.
Toggle Preset/User
User active
Green shines
3 sec.
IR signal valid received
Red
and
white shine
3 sec.
IR signal invalid received
Red
shines
0.5 sec.
100 h function active
Red / Green
flash
alternately
Red / Green
flash
alternately
Light measurement in
progress
Green
flashes 1x in
10 sec.
Green flashes
1x in 10 sec.
Wall bracket for remote
control IR-PD-DALI-1C
IR-PD-DALI-1C
15. Putting into operation of the remote control
(optional)
Settings with remote control override the potentiometer
and DIP settings.
The DIP settings are reactivated by
•
setting the potentiometers to “TEST“ and ”SUN” (see
section 24), or
•
pressing the “Reset” button on the remote control in
open state
LUXOMAT
®
IR-PD-DALI-1C
1. Check Battery:
Open battery compartment by pressing
the plastic springs together and removing
the battery-holder.
2. Note:
Using the remote control, the occupancy detector can only be
operated brightness-depending. The setting „SUN“ can only be
chosen with potentiometer A.
When using the remote control IR-PD-DALI-1C, we recommand to
set potentiometer A to „SUN“. Pressing the RESET button on the
remote control then resets the detector to brightness-independant
mode (SUN).
!
16. Settings by remote control in open state
Unlocking device –
Activation of the
programming mode
Resetting
when open:
Deletes all
values set with
the remote
control, light
OFF.
Orientation light
on/off
Automatic reading
in the current light
value as new lumi-
nance set value
or
Dimming of the
lighting to the
desired brightness
value
Adjusting of the lumi-
nance set value from
50 to 1500 Lux:
+/–
5 Lux steps
+/–
10 Lux steps
+
/
–
20 Lux steps
max
50
Lux
1500
Lux
ON
OFF
max
50
Lux
1500
Lux
ON
OFF
DSI/
DALI
Switching between DSI
and DALI program;
The Factory setting
is DALI
or
+
–
Full automatic /semi-
automatic mode (se.18)
Preset/user mode
(see section 23)
max
50
Lux
1500
Lux
ON
OFF
Follow-up time
orientation light
at
1
min
10
min
optional
optional
optional
optional
1. Start light meas-
urement by long
press of the button
(see section 17)
2. Start LED ON/OFF
by a short press of
the button
Follow-up time
Channel 1: 1 - 30 min.
Follow-up time
Channel 2 (HVAC): 5 -
60 min. or impulse
1
min
5
min
30
min
60
min
Exit programming mode
If there is no entry for
about 3 min.
the programming
mode is ended
automatically.
Permanent double lock
With this function, the
detector is permanently
locked. This mode can
only be activated during
5 sec. after closing the
detector. In this mode,
only the function „Light
ON/OFF“ can be
activated.
Red LED flashes
optional
max
50
Lux
1500
Lux
ON
OFF
t < 5 sec.
