M
A
N 7
31
5 –
26
04
12
-1
13
What should be done if ...
Possible problems
Solutions
1. The lamp being controlled
by
LUXOMAT
®
does not
switch on.
- The halogen lamp is defective.
- The mains voltage is not present.
- The twilight value switch-on threshold is not
correctly adjusted.
- Incorrect adjustment of the detection zone
- The detector is installed too high.
- The lenses in the sensor section are dirty.
- Replace the halogen lamp.
- Check the connection and the fuses.
- Correct the switch-on threshold of the
twilight switch using the rotary control.
- Change the detection zone.
- Change the installation height (maximum 3 meters).
- Clean the sensor lenses.
2. The lamp turns on too late. - The detector is installed too high.
- People approach the sensor directly.
- Change the installation height (maximum 3 meters).
- Install the sensor in such a way that the detection zone is
intersected.
3. The lamps remain perma-
nently switched-on.
- Permanent movement of a heat source in
the detection zone
- A switch has been installed parallel to the
sensor in order to enable manual switching.
- Remove the heat source from the detection zone. Check
for correct functioning by covering the lens (the lamp must
then switch-off).
- Put the switch in the “Sensor” position in order to prevent
manual switch-on.
4. Unwanted switching-on
of the light
- Permanent movement of heat sources in the
detection zone (trees, bushes being moved
by the wind, the presence of cats or dogs
in the detection zone)
- Direct sunshine on the sensor lens
- The sensor is placed directly over an air
exhaust.
- Change the range of the sensor by changing the inclina-
tion or by attaching the shades to the lens.
- Protect the lens from direct sunshine.
- Install the sensor at a different location.
5. The detector range is too
small.
- The sensor installation height is not optimal
(too high or too low)
- People directly approach the detector.
- Hillside location
- Change the installation height (2.50 meters).
- Install the sensor in such a way that the detectionzone is
intersected.
- Change the detector inclination.
6. Does not detect vehicles
- The vehicle engine is not yet warm
(weak heat source)
9. Mounting or replacement of the
halogen lamps
Always verify that the mains voltage has been isolated
whenever the halogen lamps need to be replaced.
Caution:
The floodlight can reach very high temperatures!
• Allow the lamp and the enclosure to cool down.
• Remove the fastening screw from the enclosure of the
floodlight and open the enclosure.
• Grasp the defective halogen lamp tightly and remove it
from its bracket.
• Do not touch the replacement lamps with your hands.
• Place the halogen lamp into the bracket.
• Close the enclosure and be sure that the sealing ring is
properly seated.
• Close the enclosure with the fastening screws.
8. Troubleshooting
6.
Wiring diagram
Monitoring for narrow premises, ways,
gateways or at door sills.
Monitoring two sides of a building,
warehouses, parking lots.
2 m9 m
16 m
280°
20 m
2,50 m
Monitoring for narrow premises, ways,
gateways or at door sills.
7. Detection area at 2.50 m mounting hight
LUXOMAT
®
LC-Click-N 140
LUXOMAT
®
LC-Click-N 200
LUXOMAT
®
LC-plus 280
Standard mode with 1-channel motion detector external
AL20-CdS
ALC-ELU/D
AL20-280-BM
AL20-280-BM-LED
ALC-B-360
ALC-B-360-DECO
AL2-RC-plus-130/230/280
FLC-280-LED
FL2-LED-230
AL5-RC-plus next
AL5-LC
AL1
AL4
Übersicht
L
N
L´
L
N
C1
E1
S1
Standard mode with 1-channel motion detector with NC pushbutton
Standard mode with 1-channel motion detector
T1 = NC button
Manual switching additionally possible (press opener ap-
prox. 2 sec.).
The position of the potentiometers should not be on “test”
or “sun”. If so, the pre-set time and safety values get lost.
AL20-280-BM
AL20-280-BM-LED
ALC-B-360
ALC-B-360-DECO
AL2-RC-plus-130/230/280
FLC-280-LED
FL2-LED-230
AL5-RC-plus next
AL5-LC
AL1
Übersicht
L
N
L´
L
N
C1
E1
T1
AL20-CdS
ALC-ELU/D
AL20-280-BM
AL20-280-BM-LED
ALC-B-360
ALC-B-360-DECO
AL2-RC-plus-130/230/280
FLC-280-LED
FL2-LED-230
AL5-RC-plus next
AL5-LC
AL1
max. 5 paralell
Übersicht
L
N
L´
L
N
C1
E1
L´
L
N
C1
10 Wiring diagrams
S1 = switch for permanent light
LC-plus next max. 5 parallel
10 m
140°
2,50 m
4 m
12 m
2 m
10 m
4 m
12 m
200°
2,50 m
2 m
L´ L N
PE
N
L
{
}
Motion detector
Flood light
