B+B SMARTWORK SmartFlex SR305 User Manual Download

Page: 50 / 56

SmartFlex SR305

7.5

Technical parameters of GNSS

GPS specifications

Antenna

50 Ohms – active

Protocols

NMEA 0183 v3.0

Frequency GPS

1575.42 MHz Typical

Frequency GLONASS

1597.551 MHz Min.; 1605.886 MHz Max.

Tracking Sensitivity

∗

(Open sky)

Active antenna or LNA: -159 dBm
Passive antenna: -156 dBm

Acquisition Sensitivity

∗∗

(Open sky)

Active antenna or LNA: -149 dBm
Passive antenna: -145 dBm

Cold Start Sensitivity

-145 dBm

Acquisition time (TTFF)

Warm start: 29 s Max.
Cold start: 32 s Max.

Table 32: Technical parameters of GNSS

∗

Tracking sensitivity is the lowest GNSS signal level for which the device can still detect an

in-view satellite 98 % of the time when in sequential tracking mode.

∗∗

Acquisition sensitivity is the lowest GNSS signal level for which the device can still detect

an in-view satellite 50 % of the time.

7.6

Technical parameters of WiFi

WiFi

Antenna connector

R-SMA – 50 Ohms

Supported WiFi band

2.4 GHz, 5 Ghz

Standards

802.11a, 802.11b, 802.11g, 802.11n

2.4 GHz supported channels

1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11

5 GHz supported channels

36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165

Type of device

Access point, station

Max. clients in AP mode

WiFi TX Output Power

17,3 dBm

WiFi RX Sensitivity

-96,3 dBm

Table 33: Technical parameters of WiFi

Summary of Contents for SmartFlex SR305

























































Search results

Summary of Contents for SmartFlex SR305

Reviews:

Related manuals for SmartFlex SR305

Brands by name

Popular brands

B+B SMARTWORK SmartFlex SR305, User Manual

Search results

Summary of Contents for SmartFlex SR305

Reviews:

Related manuals for SmartFlex SR305

Brands by name

Popular brands