Azkoyen HOPPER U-II Manual Download

Page: 28 / 29

VERSION 2.0

06 - 2011

WORKING CONDITIONS AND NORMS.

Optimum results from using this equipment can be obtained by meeting the

following requirements:



Power the hopper with a transformer that meets the EN-60742 Norm and

provides a maximum of 42.5 Vac without load.



Install the hopper U-II series with a maximum inclination of +/- 3ºon all axes.



Temperatures:



Storage: from -25 to +70ºC.



Working: from +5 to +55ºC.



Humidity: maximum 95% (relative humidity without condensation)



Norms that are met:



Electromagnetic compatibility:



Emission: UNE-EN 61000-6-3:2002



Radiation Emission: EN 55011:1999/A1:2000/A2:2003



Conductive Emission: EN 55011:1999/A1:2000/A2:2003



Immunity: UNE-EN 61000-6-1:2002



ESD: UNE-EN 61000-4-2:1997, /A1:1999, /A2:2001, 2004

Erratum



Radiation Immunity: UNE-EN 61000-4-3:2003, 2003 Erratum,

/A1:2004



Peaks and spikes immunity: UNE-EN 61000-4-4:2005



Magnetic Field: UNE-EN 61000-4-8:1996, /A1: 2001



Electric Security: EN 60950:2002



Meets the BACTA norm, “Binary Interface V1.0E”.



Comment: Cable for Rode U-II ccTalk connexion should be shorter than 3

meters.

Summary of Contents for HOPPER U-II






























Search results

Summary of Contents for HOPPER U-II

Reviews:

Related manuals for HOPPER U-II

Brands by name

Popular brands

Azkoyen HOPPER U-II, Manual

Search results

Summary of Contents for HOPPER U-II

Reviews:

Related manuals for HOPPER U-II

Brands by name

Popular brands