background image

going to be serviced.

Fuses:

- The main fuse of this device can be found on the rear of the device, usually next to the power inlet. 
- Only replace the fuse for a new one of the same type and rating! Do not use a fuse with a higher or lower 
rating.
- Do not bridge the fuse in any way, as the fuse is used for protection against electric shocks and short-
circuiting. The fuse is a safety measure to protect your audience from hazardous electric shocks. 
- Always replace the fuse cover over the fuse compartment. Do not use tape or other fastening materials to 
close the cover. If the fuse holder is broken, contact your local dealer and do not use the fixture.

Symbol clarification:

WEEE: 

Dispose of this product properly. This product is part of the WEEE directive – the 

Waste Electrical and Electronic Equipment directive. The requirements stated in this directive 
apply to all manufacturers and producers of electronic equipment in the EU. 

Do not dispose of this product together with regular household trash. Contact your local 
government for more information about proper disposal and recycling of electronic products in
your region. By recycling this product properly after use, we can work together to enjoy these 
products and also protect our environment from being polluted.

CE: 

The CE mark indicates that the product complies with applicable European directives and

regulations. 

Indoor use only: 

This device is designed exclusively for use indoors. The maximum 

environmental temperature should not exceed 40 degrees Celsius (104 degrees Fahrenheit)

All information and illustrations shown in this user manual are subject to change without further notice.

User manual version: 1.0

Creation date + author initials: 13-05-2015 RV Revision date + author initials: 

Summary of Contents for 9000-0019-1962


















Reviews: