Axxess AXDSPL-TY1 Installation Instructions Manual Download Page 8 | Manualshive

Page: 8 / 16

background image

8

MOBILE APP

(CONT.)

Bluetooth Connection

•

Scan

- Press this button to start the Bluetooth pairing process, then select the interface

once it is found. “Connected” will appear in the top left corner of the app once paired.

Note:

The ignition must be cycled on during this process.

•

Disconnect

- Disconnects the interface from the app.

Continued on the next page

«
...
6
7
8
9
10
...
»

Summary of Contents for AXDSPL-TY1

















Reviews:

No comments

Related manuals for AXDSPL-TY1

Brand: Voxx Pages: 7

Brand: Free Spirits Pages: 32

Brand: Abus Pages: 2

Brand: BAC Pages: 10

Brand: Baby’s Journey Pages: 2

TENSIONED CONTOUR ELECTROL

Brand: Da-Lite Pages: 8

Brand: Dacor Pages: 4

Brand: Harken Hoister Pages: 12

Brand: Yamaha Pages: 2

Brand: Federal Signal Corporation Pages: 8

Brand: Federal Signal Corporation Pages: 8

Brand: Feniex Pages: 6

Brand: Fencing SmartBox Pages: 11

Brand: Feiyu Pages: 4

Brand: FAZUA Pages: 84

Brand: GAI-Tronics Pages: 22

Brand: Oki Pages: 2

Brand: Oki Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands