background image

4

Configuration Menu

  •  The buttons on the steering wheel will be used to 

operate the configuration menu, which will be shown 
on the aftermarket radio. To enable the menu, push and 
hold the MODE button for 2 seconds. Use the Track Up 
and Track Down buttons to navigate through the menu. 
To select a menu option, push the MODE button once.

SCREEN OPERATION

Configuration Menu

Vehicle Settings

Interface Settings

Language

Version

< Back

PROGRAMMING THE ASWC-1 

INTERFACE 

(CONT.)

L.E.D. feedback

The (18) 

Red

 L.E.D. flashes represent what brand radio the ASWC-1 believes it is connected 

to. Each flash represents a different radio manufacturer. For example, if you are installing 
a JVC radio, the 

ASWC-1

 will flash (5) times. Following is a legend that dictates which 

manufacturer corresponds to which flash.

L.E.D. feedback legend

*  Note:

 

If the ASWC-1 flashes 

Red

 (7) times, and you do not have an Alpine radio connected 

to it, that means the ASWC-1 does not detect a radio connected it. Verify that the 3.5mm 

jack is connected to the correct steering wheel jack/wire in the radio.

** Note:

 

Part number AX-SWC-PARROT is required (sold separately). Also, the Parrot radio 

must be updated to rev. 2.1.4 or higher through www.parrot.com.

†  Note:

 

If you have a Clarion radio and the steering wheel controls do not work, change the radio 

type to the other Clarion radio type; same for Eclipse. The following section explains how to do this.

‡  Note:

 

If you have a Kenwood radio and the L.E.D. feedback comes back as showing as a JVC 

radio, change the radio type to a Kenwood. The following section explains how to do this.

1 flash - Eclipse (Type 1) †
2 flashes - Kenwood ‡
3 flashes - Clarion (Type 1) †
4 flashes - Sony / Dual
5 flashes - JVC
6 flashes - Pioneer / Jensen
7 flashes - Alpine *
8 flashes - Visteon
9 flashes - Valor

10 flashes - Clarion (Type 2) †
11 flashes - Metra OE
12 flashes - Eclipse (Type 2) †
13 flashes - LG
14 flashes - Parrot **
15 flashes - XITE
16 flashes - Philips
17 flashes - TBD
18 flashes - JBL

Continued on the next page

Summary of Contents for AX-LR904









Reviews: