background image

5

REV. 9/17/21 INSTAX-HYKIA1-SWC

With the key in the off position:

  •  Connect the 

16-pin harness with 

stripped leads

, and the 

AX-HYKIA1-

SWC harness

, into the 

AX-HYKIA1-SWC 

Interface

.

  •  For models equipped with a factory 

amplifier, connect the 

AX-HYKIA-SPDIF

 

(sold separately) to the 

AX-HYKIA1-

SWC interface

.

Attention!

 Do not connect the 

AX-HYKIA1-SWC 

harness

 to the vehicle’s wiring harness until 

Step 2 of Programming.

Attention!

  

If retaining steering wheel 

controls, ensure that the jack/wire is 

connected to the radio before proceeding. 

If this step is skipped, the interface will need 

to be reset for the steering wheel controls 

to function.

INSTALLATION

Flash Count  

Radio

1

Eclipse  (type 1) †

2

Kenwood ‡

3

Clarion  (type 1) †

4

Sony / Dual

5

JVC

6

Pioneer / Jensen

7

Alpine *

8

Visteon

9

Valor

10

Clarion  (type 2) †

11

Metra OE

12

Eclipse  (type 2) †

13

LG

14

Parrot **

15

XITE

16

Philips

17

TBA

18

JBL

19

Insane Audio

20

Magnadyne/Axxera

21

Boss

L.E.D. Feedback Legend

L.E.D. feedback

The (21) 

Red

 L.E.D. flashes represent which 

brand radio the 

AX-HYKIA1-SWC

 detects.

Each flash represents a different radio 
manufacturer. For example, if you are 
installing a JVC radio, the 

AX-HYKIA1-SWC

 

will flash 

Red

 (5) times, and then stop. 

Following is the 

L.E.D Feedback Legend

 

a legend that indicates which radio 
Manufacturer corresponds to which flash.

*Note:

  If the 

AX-HYKIA1-SWC

 flashes 

Red

 

(7) times, and you do not have an Alpine 

radio connected to it, that means the 

ASWC-1 does not detect a radio connected 

it. Verify that the 3.5mm jack is connected 

to the correct steering wheel jack/wire in 

the radio.

** Note: 

 The AX-SWC-PARROT is required 

(sold separately). Also, the Parrot radio 

must be updated to rev. 2.1.4 or higher 

through www.parrot.com.

†  Note:

  

If you have a Clarion radio and 

the steering wheel controls do not work, 

change the radio type to the other 

Clarion radio type; same for Eclipse. 

Refer to the “Programming Information” 

document online

.

‡  Note:

  If you have a Kenwood radio 

and the L.E.D. feedback comes back 

as showing as a JVC radio, change the 

radio type to a Kenwood. Refer to the 

“Programming Information” document 

online.

Continued on the next page

Summary of Contents for AX-HYKIA1-SWC













Reviews: