background image

CAUTION! 

 All accessories, switches, climate 

controls panels, and especially air bag indicator 

lights must be connected before cycling the 

ignition. Also, do not remove the factory radio 

with the key in the on position, or while the 

vehicle is running. 

AX-AU12-SWC

I N S TA L L AT I O N I N S T R U C T I O N S

AxxessInterfaces.com 

© COPYRIGHT 2018 METRA ELECTRONICS CORPORATION 

REV. 7/19/18 INSTAX-AU12-SWC

INTERFACE FEATURES

INTERFACE COMPONENTS

TOOLS REQUIRED

• Wire cutter • Crimp tool• Solder gun • Tape
• Connectors (example: butt-connectors, bell caps, etc.)

TABLE OF CONTENTS

Connections to be made .......................................................2-6
- For LD-BX-AU1 applications equipped with a Bose amp ........2
- For LD-BX-AU1 applications equipped without a Bose amp ..3
- For LD-BX-AU2 applications equipped with a Bose amp ........4
- For LD-BX-AU2 applications equipped without a Bose amp ..5
- 3.5mm jack steering wheel control retention .........................6
Installing the AX-AU12-SWC ..................................................... 6
Initializing the AX-AU12-SWC ................................................... 6
Troubleshooting the AX-AU12-SWC ......................................... 6
Steering wheel control settings ...........................................7-9
  L.E.D. feedback .....................................................................7
  Changing radio type ............................................................7
  Remapping the steering wheel control buttons .............. 8
  Dual assignment instructions (long button press) .......... 9
  Resetting the AX-AU12-SWC ..............................................10

Audi 

Data Interface with SWC

 

2002-2015

APPLICATIONS

•  Provides accessory power 

(12-volt 10-amp) 

•  Retains R.A.P. (retained 

accessory power) 

•  Provides NAV outputs (parking 

brake, reverse, speed sense) 

•  Retains audio controls on 

the steering wheel

•  Designed for both Bose, 

and non-Bose models

•  Retains balance and fade 
•  Micro “B” USB updatable

• AX-AU12-SWC interface
• LD-BX-AU1 harness

• LD-BX-AU2 harness
• 16-pin harness with stripped leads

• Female 3.5mm connector with stripped leads

AUDI

Applications below use  

 

LD-BX-AU1:

A3 * 

2006-2013

A4/RS 4/S4 w/ NAV 

2005-2008

A4/RS 4/S4 

2007-2008

A4/RS 4/S4* 

2006

A4/S4 

Convertible

 

2009

TT/TTS 

2008-2015 

Applications below use  

 

LD-BX-AU2:

A3 † 

2006-2007

A4/S4 ‡ 

2006

A4/S4 

2002-2005

A6/RS 6/S6 

2002-2004

allroad 

2004-2005

TT 

2002-2006

*  Only for models with either a 

  Symphony Plus or a NAV radio.
†  Non-navigation Concert or 

  Symphony radio only
‡  Non-navigation Symphony 

  radio only

Summary of Contents for AX-AU12-SWC













Reviews: