SETUP & USE
(continued)
FCC INFORMATION
This device complies with part 15 of FCC Rules. Operation is subject to the following
two conditions: (1) The device may not cause harmful interference, and (2) This
device must accept any interference received, including interference that may
cause undesired operation.
CAUTION
Changes and modifications not expressly approved by AXVUE may void the users
authority to operate this equipment.
NOTE
This equipment has been tested and found to comply with the limits for a Class B
digital device,
Pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
CAUTION
1. To comply with the FCC RF exposure compliance requirement, a separation
distance of 20 cm must be maintained between the antenna of this device and all
persons.
2. This transmitter most not be co-located or operating in conjunction with any other
antenna or transmitter.
DO NOT EXPOSE TO RAIN OR MOISTURE
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT SAFETY INSTRUCTIONS
• Make sure you read this instruction carefully before using the product.
• Store this instruction safely for your future reference.
• Ensure that you read the “Warning” section of the product package and this instruction carefully.
• Use the product properly by following this instruction.
• Wipe the product by wet towel after you take it down from the wall.
• Avoid possible danger by following manufacturer’s instruction.
• Do not using the product in humid place or contact with liquid, like bathtub, hand washing sink, kitchen sink, laundry tub,
humid basement, swimming pool, etc.
• Ensure the product is installed in a flat place. Otherwise, it will cause serious personal injury and product damage when
dropped.
• Only follow this instruction and use installation tools provided by the manufacturer to set up the product.
• The slots and holes on the product are used for ventilation, please ensure that it is not covered or blocked by other objects.
• Do not place the product on bed, sofa, rug or other similar places, it will block or cover the slots and holes on the product.
Do not place the product in a closed bookcase or shelf unless it has particular part for ventilation.
• This product should be connected with certain power supply unit, if you are not sure about the power supply system in your
home, please contact with your product dealer and local power supply company. Please refer to the operating instruction if
you want to operate the product in portable/battery mode or by connecting with other power supply sources.
• Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against
them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
• An outside antenna system should not be located in the vicinity of overhead power lines or other electrical lines or power
circuits, it will cause interference for the signal transmission. When installing an outside antenna system, extremely attention
should be paid to avoid touching such power lines or circuits, otherwise, you will have possible danger of electrical shock.
• Do not overload wall outlet, extension cords or convenience receptacles, this can be cause a risk of fire or electrical shock.
• Do not insert any tiny objects into the product’s inside, it may touch dangerous voltage point or cause short-circuit, this can
be cause a risk of fire or electrical shock. Any kind of liquid spillage happens on the product should be avoid.
• Do not maintain the product by yourself as opening and removing the covering, this may expose you to dangerous voltage
or other hazards. Please contact with qualified service personnel for maintaining.
• Unplug the product from wall outlet and contact with qualified service personnel if you have problems as below:
- When the power-supply cord or plug has been damaged.
- If liquid has been spilled, or objects have fallen into the product.
- If the product has been exposed to rain or water.
- If the product didn’t operate normally by following the operating instructions, please only adjust those controls which are
covered by the operating instructions. An improper adjustment of other controls may result in product damage,
it will also require extensive work from qualified service personnel to restore the product to its normal operation mode.
- If the products has been dropped or damaged in any way, or when the product shows a distinct change in
performance - this indicated that the product need to be maintained.
• Replacement parts - When replacement parts are required, be sure the service technician has used replacement parts
specified by the manufacturer or its have the same characteristics as the original part. Unauthorized substitutions may
result in fire, electrical shock or other hazards.
• Safety Check - Upon completion of any service or repairs to this product, ask the service technician to run safety checks on
the product to confirm that it is in a proper operating condition.
• The product only can be mounted on the wall or ceiling as recommended by the manufacturer.
• The product should be kept away from heat sources, such as radiator, heat registers, stoves or other products (including
amplifier) which can produce heat.
The SCAN, SELECT, ADD, DELETE, VIEW CAMERA options are only available when multiple
cameras connected with the monitor. Order extra cameras by visiting us at
www.axvue.com or search “Axvue Baby monitor” on Amazon.
TO DELETE A CAMERA
TO CONTROL THE CAMERA
Favorite Features
Press and hold the
Zoom /
Talk Back
button on the
monitor to activate two-way
communication mode.
* Press the AUTO-SCAN button again to stop scanning.
DIGITAL ZOOM IN & OUT
x 1
x 1
Zoom x 2
TWO-WAY COMMUNICATION
OK
OK
vox
TO SELECT A CAMERA
cam 1
85°F
cam 2
85°F
OK
1
2
85°F
85°F
TO ADJUST SCREEN COLOR TEMPERATURE
OK
TO SET UP VOX - VIDEO ON CRYING
85°F
vox1 85°F
Long Press
Press & hold
for 2 seconds
cam 1 vox1
85°F
OFF 1 2 3
OK
vox3 85°F
cam 1
85°F
scan 2
85°F
TO SCAN ALL CAMERAS (AUTO-SCAN)
Press &
hold
85°F
BRIGHTNESS
ADJUSTMENT
VOLUME
CONTROL
TEMPERATURE
DISPLAY
85°F
85°F
1
1
2
70°F
21°C
1
4
1
2
3
OK
2
3
OK
8
OK
9
OK
5
OK
4
8
5
OK
6
7
OK
OK
1
2
6
7
OK
2
3
OK
2
3
OK
VOX
85°F
VOX
1
CAM SIGNAL WILL BE LOST!
CANCEL
OK
YES
8
OK
10
OK
vox
OK
OK
732-0E9650W-0704
AXVUE INC.
Revised at 09/2020
*Any updated or revised version please refer to axvue official website
.
AXVUE stands behind all of its products.
If you are not completely satisfied or have any questions,
please contact us at https://www.axvue.com
Connect with us:
VIDEO
ON/OFF
°F °C
Step 5:
OK
1
3
2
4
Red LED flashs
85°F
Use the arrow buttons to
control the camera to pan
left / right and tilt up / down.
